Код: Выделить всё
SN и MAC подтерты
файл вложением 1.txt пишет не верное расширение
**************************************************************
hi3516cv300 System startup
U-Boot 2010.06 (Jun 01 2020 - 08:20:12)
Check Flash Memory Controller v100 ... Found
SPI Nand(cs 0) ID: 0xc8 0x21 Name:"F50L1G41A"
Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:8bit/512
ECC provided by Flash Memory Controller
SPI Nand total size: 128MB
MMC:
EMMC/MMC/SD controller initialization.
Card did not respond to voltage select!
No EMMC/MMC/SD device found !
*** Warning - bad CRC or NAND, using default environment
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
Set gpio: 60->0
Set gpio: 0->0
Set gpio: 73->1
Set gpio: 27->1
Set gpio: 72->1
No mmc found
NAND read: device 0 offset 0x200000, size 0x500000
5242880 bytes read: OK
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.18.20
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4766539 Bytes = 4.5 MiB
Load Address: 80008000
Entry Point: 80008000
Loading Kernel Image ... OK
OK
Starting kernel ...
Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpu
Linux version 3.18.20 (root@runner-1uqpbhwg-project-22-concurrent-0) (gcc versio n 4.9.4 20150629 (prerelease) (Hisilicon_v500_20170615) ) #1 Mon Aug 30 08:04:45 UTC 2021
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
CPU: VIVT data cache, VIVT instruction cache
Machine model: Hisilicon Hi3516CV300 DEMO Board
Memory policy: Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: mem=64M console=ttyAMA0,115200 rootfstype=ramfs mtdparts=hi nand:1024K(boot),1024K(tech),5120K(kernel),16384K(app),-(config) hw_type=405 ubi .mtd=3,2048
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 57244K/65536K available (4124K kernel code, 190K rwdata, 1100K rodata, 1 908K init, 256K bss, 8292K reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
vmalloc : 0xc4800000 - 0xff000000 ( 936 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc0522748 (5226 kB)
.init : 0xc0523000 - 0xc0700000 (1908 kB)
.data : 0xc0700000 - 0xc072f980 ( 191 kB)
.bss : 0xc072f980 - 0xc076fbb8 ( 257 kB)
SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:16 nr_irqs:16 16
VIC @c4800000: id 0x00641190, vendor 0x41
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655765682ns
Console: colour dummy device 80x30
Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0x803f1040 - 0x803f1098
devtmpfs: initialized
VFP support v0.3: not present
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
Serial: AMBA PL011 UART driver
12100000.uart: ttyAMA0 at MMIO 0x12100000 (irq = 21, base_baud = 0) is a PL011 r ev2
console [ttyAMA0] enabled
SCSI subsystem initialized
ssp-pl022 12120000.spi: ARM PL022 driver, device ID: 0x00800022
ssp-pl022 12120000.spi: mapped registers from 0x12120000 to c486c000
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switched to clocksource arm,sp804
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
futex hash table entries: 256 (order: -1, 3072 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 111
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
pinctrl-single 12040000.pinmux: 66 pins at pa c48c8000 size 264
pinctrl-single 12040800.pinconf: 76 pins at pa c48ca800 size 304
pl061_gpio 12140000.gpio: PL061 GPIO chip @0x12140000 registered
pl061_gpio 12141000.gpio: PL061 GPIO chip @0x12141000 registered
pl061_gpio 12142000.gpio: PL061 GPIO chip @0x12142000 registered
pl061_gpio 12143000.gpio: PL061 GPIO chip @0x12143000 registered
pl061_gpio 12144000.gpio: PL061 GPIO chip @0x12144000 registered
pl061_gpio 12145000.gpio: PL061 GPIO chip @0x12145000 registered
pl061_gpio 12146000.gpio: PL061 GPIO chip @0x12146000 registered
pl061_gpio 12147000.gpio: PL061 GPIO chip @0x12147000 registered
pl061_gpio 12148000.gpio: PL061 GPIO chip @0x12148000 registered
brd: module loaded
hisi-sfc hisi_spi_nor.0: unrecognized JEDEC id bytes: ff, c8, 21
hisi-sfc hisi_spi_nor.0: spi nor register fail!
hisi-sfc: probe of hisi_spi_nor.0 failed with error -2
SPI Nand ID Table Version 2.2
SPI Nand(cs 0) ID: 0xc8 0x21
nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x21
nand: GD/ESMT F50L1G41A
nand: 128MiB, SLC, page size: 2048
Nand(Auto): OOB:64B ECC:8bit/512
nand: ECC provided by Flash Memory Controller
5 cmdlinepart partitions found on MTD device hinand
5 cmdlinepart partitions found on MTD device hinand
Creating 5 MTD partitions on "hinand":
0x000000000000-0x000000100000 : "boot"
0x000000100000-0x000000200000 : "tech"
0x000000200000-0x000000700000 : "kernel"
0x000000700000-0x000001700000 : "app"
0x000001700000-0x000008000000 : "config"
libphy: hisi_femac_mii_bus: probed
hisi-femac 10050000.ethernet: phy_id=0x001cc816, phy_addr=1, phy_mode=rmii
hisi-femac 10050000.ethernet: using random MAC address 1a:f6:5b:39:af:0b
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform: EHCI generic platform driver
ehci-platform 10120000.ehci: EHCI Host Controller
ehci-platform 10120000.ehci: new USB bus registered, assigned bus number 1
ehci-platform 10120000.ehci: irq 31, io mem 0x10120000
ehci-platform 10120000.ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-platform: OHCI generic platform driver
ohci-platform 10110000.ohci: Generic Platform OHCI controller
ohci-platform 10110000.ohci: new USB bus registered, assigned bus number 2
ohci-platform 10110000.ohci: irq 32, io mem 0x10110000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
hibvt-i2c 12110000.i2c: hibvt-i2c0@100000hz registered
hibvt-i2c 12112000.i2c: hibvt-i2c1@100000hz registered
himci: mmc host probe
himci: mmc host probe
himci: mmc host probe
TCP: cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
UBI: attaching mtd3 to ubi0
UBI: scanning is finished
UBI warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling , reserved 16, need 20
UBI: attached mtd3 (name "app", size 16 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 128, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 140 1014055
UBI: available PEBs: 0, total reserved PEBs: 128, PEBs reserved for bad PEB hand ling: 16
UBI: background thread "ubi_bgt0d" started, PID 37
Freeing unused kernel memory: 1908K (c0523000 - c0700000)
_ _ _ _ _ _ _ _ _ _ _ _
\ _ _ _ _ _ ___
/ /__/ \ |_/
/ __random: S01udev urandom read with 2 bits of entropy available
/ - _ ___
/ / / / / /
_ _ _ _/ / / \_/ \_ ______
___________\___\__________________
[RCS]: /etc/init.d/S01udev
udev[45]: starting version 167
[RCS]: /etc/init.d/S80network
[RCS]: /etc/init.d/S90hibernate
[RCS]: /etc/init.d/S99custom
UBIFS: static UBI volume - read-only mode
UBIFS: mounted UBI device 0, volume 0, name "app", R/O mode
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/20 48 bytes
UBIFS: FS size: 12443648 bytes (11 MiB, 98 LEBs), journal size 2412544 bytes (2 MiB, 19 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID B8B06ACE-5FAC-4DC0-BC57-DDF38 60A69BB, small LPT model
[00:00:04][VC-SYS-Daemon][VCSDaemonInitializer.cpp:54][INFO]: VC-SYS version v1. 2.6-18-g1857204
[00:00:04][VC-SYS-Daemon][GPIOController.cpp:194][INFO]: Initialized peripherial s for hw_type=405
[00:00:04][VC-SYS-Daemon][LEDController.cpp:141][INFO]: Setting auto leds preset . ID = 2
[00:00:04][VC-SYS-Daemon][NetworkController.cpp:751][INFO]: Setting (1) as main interface. Old main interface is (-1)
yaffs: dev is 32505860 name is "mtdblock4" rw
yaffs: passed flags ""
[09:00:04][FWUPDATER][FWUpdater.cpp:183][INFO]: No files to restore from techjso n
[00:00:05][VC-SYS-Daemon][GPIOController.cpp:266][ERROR]: Invalid key name wps
mount: mounting /dev/mmcblk0p1 on /mnt/mmc01 failed: No such file or directory
Initializing motor modules
mmz_start: 0x84000000, mmz_size: 192M
2735xxxx
*** Board tools : ver0.0.1_20121120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x1201002c: 0x00000000 --> 0x0604800D
[END]
sh: can't open 'config_sensor.sh': No such file or directory
Module himedia: init ok
Hisilicon Media Memory Zone Manager
The module param setup_allocator is hisi
hi_osal 1.0 init success!
hi3516cv300_base: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
load sys.ko for Hi3516CV300...OK!
load region.ko for Hi3516CV300...OK!
load vgs.ko for Hi3516CV300...OK!
load viu.ko for Hi3516CV300...OK!
ISP Mod init!
load vpss.ko for Hi3516CV300...OK!
load vou.ko for Hi3516CV300...OK!
load rc.ko ...OK!
load venc.ko ...OK!
load chnl.ko for Hi3516CV300...OK!
load vedu.ko ...OK!
load h264e.ko ...OK!
load h265e.ko ...OK!
load jpege.ko ...OK!
load ive.ko for Hi3516CV300...OK!
load hi_piris.ko OK!
load ai.ko OK!
load ao.ko OK!
load aenc.ko OK!
load adec.ko OK!
load acodec.ko for Hi3516CV300...OK!
insert audio
load hi_mipi driver successful!
Load hi_cipher.ko success.
hirtc init ok. ver=Aug 30 2021, 08:05:07.
Hisilicon Watchdog Timer: 0.01 initialized. default_margin=60 sec (nodeamon= 1)
hiwtdg init ok. ver=Aug 30 2021, 08:05:08.
==== Your input Sensor type is ov2735 ====
[00:00:10][VC-SYS-Daemon][ServerMsgDispatcher.cpp:281][INFO]: Read RTC msg recieved
[RTC_READ]
No upgrade log found.
[09:38:33][Agent-Updater][AgentUpdater.cpp:169][INFO]: Staring agent updater, version v1.1.13-b254554
[09:38:33][Agent-Updater][Tools.cpp:350][INFO]: Detected LZMA invokation type: -cd
[09:38:33][Agent-Updater][AgentUpdater.cpp:2343][INFO]: Read config file /tmp/ag-upd.json
[09:38:33][Agent-Updater][AgentUpdater.cpp:2280][INFO]: Added updater url: 'https://camera-updater.camera.rt.ru/agent/:platform/:env/version.json'
[09:38:33][Agent-Updater][AgentUpdater.cpp:2391][INFO]: [QR MODE] Normal.
I0212 09:38:33.845999 159 LogCache.cc:21] Log cache initialized, size = 500000 bytes
I0212 09:38:33.848958 159 Main.cc:53] Starting VC-HAL, version v2.13.3-b254554 (built on Aug 30 2021 at 08:09:59) ...
[09:38:33][Agent-Updater][AgentUpdater.cpp:215][INFO]: Security props = ''
[09:38:33][Agent-Updater][AgentUpdater.cpp:216][INFO]: Security props.once = ''
[09:38:34][Agent-Updater][AgentUpdater.cpp:2207][INFO]: [TRUSTED CA] Reading '/opt/share/vc/cacert.pem'
[09:38:34][Agent-Updater][AgentUpdater.cpp:2218][INFO]: [TRUSTED CA] Loaded 7 root certificates
[09:38:34][Agent-Updater][EvilConfig.cpp:110][INFO]: SetState (0)
W0212 09:38:34.037372 159 Utils.cc:687] System may be unstable! Counter is 2 of 5
[09:38:34][Agent-Updater][AgentGuard.cpp:32][INFO]: AgentGuard init
[09:38:34][Agent-Updater][AgentGuard.cpp:127][INFO]: Check ag-cfg update: /config/vc/ag-cfg.json - exists; bundled md5=,current md5=57bb90a5eecbb110dc7de89ef3e6a540
[09:38:34][Agent-Updater][AgentGuard.cpp:130][WARNING]: Rewriting ag-cfg
[09:38:34][Agent-Updater][EnvController.cpp:105][INFO]: Syncing agent(prod) and system envs(prod)
[09:38:34][Agent-Updater][AgentUpdater.cpp:2170][INFO]: Checking password. Env = prod
WARNING: Logging before InitGoogleLogging() is written to STDERR
I0212 09:38:34.071058 166 InterConn.cc:606] Connecting to 127.0.0.1:10000
I0212 09:38:34.072329 166 InterConn.cc:722] TcpConn error
[09:38:34][Agent-Updater][HalApi.cpp:243][ERROR]: resetRootPassword() error: checkSocket() failed: Connection refused
E0212 09:38:34.099238 159 Utils.cc:118] GET MAC: No running network interfaces found!
E0212 09:38:34.101191 159 Utils.cc:118] GET MAC: No running network interfaces found!
I0212 09:38:34.210961 159 DevInfo.cc:265] Tech json: {
"sn": "xxxxxxxxxxxx",
"wlan-mac": "xx:xx:xx:xx:xx:xx",
"hw-type": "405",
"eth-mac": "xx:xx:xx:xx:xx:xx"
}