Восстановление IPC-HFW1100SP

killeo
Сообщения: 50
Зарегистрирован: 01 апр 2015, 15:12

Восстановление IPC-HFW1100SP

Сообщение killeo » 11 мар 2016, 13:04

Прошу помощи.
IPC-HFW1100SP
Перезагружается.

rs232->tftp->(прошивка HFW11XX(с польского FTP))-> OK -> reboot
перезагружается на том-же месте

rs232->tftp->(прошивка HFW11XX по отдельности 12 файлов .img (найдена у братьев итальянцев))
run up
run da
run ... т.д., как написано в printenv
-> OK -> reboot

тоже самое.

Код: Выделить всё

U-Boot 2010.06-svn2134 (May 26 2014 -16:15:03)
DRAM: 256MiB
Check spi flash controller v 350... Found
Spi(cs1):Block:64KB Chip:16MB Name:"MX25L128XX"
boot from spi
partition file version 2
rootfstype squashfs root /dev/mtdblock7
In:    serial
Out:   serial
Err:   serial
TEXT_BASE:81000000
        Hisilicon ETH net controler
MAC:   90-02-A9-44-C6-C4
UP_PORT : phy status change : LINK=UP : DUPLEX=FULL : SPEED=100M
TFTP from server 192.168.254.254; our IP address is 192.168.1.108; sending thro1
Download Filename 'upgrade_info_7db780a713a4.txt'.
Download to address: 0x84000000
Downloading: *
Retry count exceeded; starting again
Fail to get info file!
Init error!                                                                     
Hisilicon ETH net controler                                                     
miiphy_register: non unique device name '0:1'                                   
miiphy_register: non unique device name '0:2'                                   
MAC:   90-02-A9-44-C6-C4                                                       
UP_PORT : phy status change : LINK=DOWN : DUPLEX=FULL : SPEED=100M             
UP_PORT : phy status change : LINK=UP : DUPLEX=FULL : SPEED=100M               
TFTP from server 192.168.254.254; our IP address is 192.168.1.108; sending thro1
Download Filename 'failed.txt'.                                                 
Download to address: 0x82000000                                                 
Downloading: *                                                                 
Retry count exceeded; starting again                                           
SPI probe: 16384 KiB hi_sfc at 0:0 is now current device                       
## Booting kernel from Legacy Image at 82000000 ...                             
   Image Name:   Linux-3.0.8                                                   
   Image Type:   ARM Linux Kernel Image (uncompressed)                         
   Data Size:    1337924 Bytes = 1.3 MiB                                       
   Load Address: 80008000                                                       
   Entry Point:  80008000                                                       
   Loading Kernel Image ...OK                                                   
OK                                                                             
partition file version 2                                                       
rootfstype squashfs root /dev/mtdblock7                                         
cmdLine mem=85M console=ttyS0,115200 root=/dev/mtdblock7 rootfstype=squashfs   
crashflasg:1, logmagic:54410011.                                               
                                                                               
Starting kernel ...                                                             
Uncompressing Linux... done, booting the kernel.                               
Linux version 3.0.8 (huang_zhendi@localhost.localdomain) (gcc version 4.4.1 (Hi4
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177                   
CPU: VIVT data cache, VIVT instruction cache                                   
Machine: hi3518                                                                 
appauto=0                                                                       
dh_keyboard=0                                                                   
ethaddr0=90:2:a9:44:c6:c4                                                       
ethaddr1=0:0:0:0:0:0                                                           
wifiAddr=0:0:0:0:0:0                                                           
lip0=192.168.1.108                                                             
lip1=0.0.0.0                                                                   
id=TZC4CU029W00086                                                             
U-Boot 0x40000 0x80000 0x0                                                     
hwid 0x40000 0xc0000 0x0                                                       
partition 0x40000 0x100000 0x0                                                 
custom 0x20000 0x140000 0x0                                                     
product 0x20000 0x160000 0x0                                                   
Kernel 0x160000 0x180000 0x0                                                   
web 0x220000 0x2e0000 0x0                                                       
romfs 0x1a0000 0x500000 0x0                                                     
user 0x840000 0x6a0000 0x0                                                     
syslog 0x60000 0xee0000 0x0                                                     
config 0x60000 0xf40000 0x0                                                     
backup 0x60000 0xfa0000 0x0                                                     
num parts is 12.                                                               
Ignoring unrecognised tag 0x54410011                                           
Memory policy: ECC disabled, Data cache writeback                               
AXI bus clock 220000000.                                                       
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 21590     
Kernel command line: mem=85M console=ttyS0,115200 root=/dev/mtdblock7 rootfstyp
dh_keyboard:0                                                                   
PID hash table entries: 512 (order: -1, 2048 bytes)                             
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)                 
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)                   
Memory: 85MB = 85MB total                                                       
Memory: 82548k/82548k available, 4492k reserved, 0K highmem                     
Virtual kernel memory layout:                                                   
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)                               
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)                               
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)                               
    vmalloc : 0xc5800000 - 0xfe000000   ( 904 MB)                               
    lowmem  : 0xc0000000 - 0xc5500000   (  85 MB)                               
    modules : 0xbf000000 - 0xc0000000   (  16 MB)                               
      .init : 0xc0008000 - 0xc0020000   (  96 kB)                               
      .text : 0xc0020000 - 0xc035d000   (3316 kB)                               
      .data : 0xc035e000 - 0xc03782e0   ( 105 kB)                               
       .bss : 0xc0378304 - 0xc038f758   (  94 kB)                               
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1         
NR_IRQS:32 nr_irqs:32 32                                                       
sched_clock: 32 bits at 110MHz, resolution 9ns, wraps every 39045ms             
Console: colour dummy device 80x30                                             
Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632)                         
pid_max: default: 32768 minimum: 301                                           
Mount-cache hash table entries: 512                                             
CPU: Testing write buffer coherency: ok                                         
devtmpfs: initialized                                                           
NET: Registered protocol family 16                                             
Serial: AMBA PL011 UART driver                                                 
uart:0: ttyS0 at MMIO 0x20080000 (irq = 5) is a PL011 rev2                     
console [ttyS0] enabled                                                         
uart:1: ttyS1 at MMIO 0x20090000 (irq = 5) is a PL011 rev2                     
bio: create slab <bio-0> at 0                                                   
usbcore: registered new interface driver usbfs                                 
usbcore: registered new interface driver hub                                   
usbcore: registered new device driver usb                                       
Switching to clocksource timer1                                                 
NET: Registered protocol family 2                                               
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)                 
TCP established hash table entries: 4096 (order: 3, 32768 bytes)               
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)                       
TCP: Hash tables configured (established 4096 bind 4096)                       
TCP reno registered                                                             
UDP hash table entries: 256 (order: 0, 4096 bytes)                             
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)                         
NET: Registered protocol family 1                                               
RPC: Registered named UNIX socket transport module.                             
RPC: Registered udp transport module.                                           
RPC: Registered tcp transport module.                                           
RPC: Registered tcp NFSv4.1 backchannel transport module.                       
squashfs: version 4.0 (2009/01/31) Phillip Lougher                             
JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.                           
msgmni has been set to 161                                                     
io scheduler noop registered                                                   
io scheduler deadline registered (default)                                     
io scheduler cfq registered                                                     
Spi id table Version 1.22                                                       
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18                                     
SPI FLASH start_up_mode is 3 Bytes                                             
Spi(cs1):                                                                       
Block:64KB                                                                     
Chip:16MB                                                                       
Name:"MX25L128XX"                                                               
spi size: 0x16777216                                                           
chip num: 1                                                                     
Creating 12 MTD partitions on "hi_sfc":                                         
0x000000080000-0x0000000c0000 : "U-Boot"                                       
0x0000000c0000-0x000000100000 : "hwid"                                         
0x000000100000-0x000000140000 : "partition"                                     
0x000000140000-0x000000160000 : "custom"                                       
0x000000160000-0x000000180000 : "product"                                       
0x000000180000-0x0000002e0000 : "Kernel"                                       
0x0000002e0000-0x000000500000 : "web"                                           
0x000000500000-0x0000006a0000 : "romfs"                                         
0x0000006a0000-0x000000ee0000 : "user"                                         
0x000000ee0000-0x000000f40000 : "syslog"                                       
0x000000f40000-0x000000fa0000 : "config"                                       
0x000000fa0000-0x000001000000 : "backup"                                       
Fixed MDIO Bus: probed                                                         
himii: probed                                                                   
PPP generic driver version 2.4.2                                               
NET: Registered protocol family 24                                             
tun: Universal TUN/TAP device driver, 1.6                                       
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>                         
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver                     
hiusb-ehci hiusb-ehci.0: HIUSB EHCI                                             
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1         
hiusb-ehci hiusb-ehci.0: irq 15, io mem 0x100b0000                             
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00                             
hub 1-0:1.0: USB hub found                                                     
hub 1-0:1.0: 1 port detected                                                   
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver                         
hiusb-ohci hiusb-ohci.0: HIUSB OHCI                                             
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2         
hiusb-ohci hiusb-ohci.0: irq 16, io mem 0x100a0000                             
hub 2-0:1.0: USB hub found                                                     
hub 2-0:1.0: 1 port detected                                                   
TCP bic registered                                                             
TCP cubic registered                                                           
NET: Registered protocol family 10                                             
NET: Registered protocol family 17                                             
NET: Registered protocol family 15                                             
Registering the dns_resolver key type                                           
registered taskstats version 1                                                 
�VFS: Mounted root (squashfs filesystem) readonly on device 31:7.               
devtmpfs: mounted                                                               
Freeing init memory: 96K                                                       
                                                                               
proc_file_read: Apparent buffer overflow!                                       
proc_file_read: Apparent buffer overflow!                                       
proc_file_read: Apparent buffer overflow!                                       
.'��ѕ����������ѕ��quoted string                                                 
keyboard = 0                                                                   
Hisilicon Media Memory Zone Manager                                             
hi3518_base: module license 'Proprietary' taints kernel.                       
Disabling lock debugging due to kernel taint                                   
Hisilicon UMAP device driver interface: v3.00                                   
pa:85500000, va:c5a00000                                                       
load sys.ko for Hi3518...OK!                                                   
load viu.ko for Hi3518...OK!                                                   
ISP Mod init!                                                                   
load vpss.ko ....OK!                                                           
load venc.ko for Hi3518...OK!                                                   
load group.ko for Hi3518...OK!                                                 
load chnl.ko for Hi3518...OK!                                                   
load h264e.ko for Hi3518...OK!                                                 
load jpege.ko for Hi3518...OK!                                                 
load rc.ko for Hi3518...OK!                                                     
load region.ko ....OK!                                                         
                                                                               
                                                                               
[OSA-DRV] OSA Build on Nov 27 2014 at 13:41:35.                                 
[OSA-DRV] SVN NUM: 3047.                                                       
                                                                               
[OSA-DRV] Monitor    Task   pid=474   tid=474                                   
                                                                               
                                                                               
[LOG-DRV] LOG Build on Mar  5 2014 at 17:06:42.                                 
[LOG-DRV] SVN NUM: 5356.                                                       
                                                                               
[LOG-DRV] ramStart:0x0;ramSize:0x0;select:0                                     
[OSA-DRV] Char device create OK !                                               
[LOG-DRV] coreId = 0, logLevel = 2                                             
[LOG-DRV] coreId = 1, logLevel = 2                                             
[LOG-DRV] coreId = 2, logLevel = 2                                             
[LOG-DRV] coreId = 3, logLevel = 2                                             
[LOG-DRV] coreId = 4, logLevel = 2                                             
[LOG-DRV] coreId = 5, logLevel = 2                                             
00:00:04|[Binder] Binder.ko Build on Sep  3 2013 at 10:07:04.                   
00:00:04|[Binder] SVN NUM: 1366.                                               
                                                                               
00:00:04|[Binder] Create binder memory pool(size:524288) OK!                   
00:00:04|[Binder] Create binder memory pool(size:3145728) OK!                   
00:00:04|[Binder] NameServer Initial OK !                                       
00:00:04|[Binder] Binder Initial OK !                                           
00:00:04|[OSA-DRV] Char device create OK !                                     
00:00:04|[Binder] SR driver initial OK !                                       
00:00:04|[OSA-DRV] Char device create OK !                                     
00:00:04|[Binder] NS driver initial OK !                                       
00:00:04|[OSA-DRV] Char device create OK !                                     
00:00:04|[Binder] Binder driver initial OK !                                   
00:00:04|[SPF] SPF Build on Apr 23 2014 at 20:23:56.                           
00:00:04|[SPF] SVN NUM: 5976.                                                   
                                                                               
00:00:04|[SPF] SIL initial OK !                                                 
00:00:04|[SPF] SPF initial ok !                                                 
00:00:04|[OSA-DRV] Char device create OK !                                     
00:00:04|[SPF] SPF Proc Create OK!!!                                           
00:00:04|[SPF] SPF driver initial ok !                                         
00:00:04|[prc] PRC Driver Build on Jun 12 2014 at 16:05:38.                     
00:00:04|[prc] SVN NUM: 2234.                                                   
                                                                               
00:00:04|[prc] Start to init module!                                           
00:00:04|[prc] pinmux init ok                                                   
00:00:04|[prc] gpio soc init ok                                                 
00:00:04|[prc] spi init ok                                                     
00:00:04|[prc] IIC init ok                                                     
00:00:04|[prc] PRC_wdtInit OK                                                   
00:00:04|[prc] PRC_rtcInit OK!                                                 
00:00:04|[prc] i2c businit ok                                                   
00:00:04|[prc] DMA init ok                                                     
00:00:04|[SPF] Dai 3 register OK !                                             
00:00:04|[prc] IIS init: ok                                                     
00:00:04|[SPF] codecType 32 register OK !                                       
00:00:04|[prc] Codec init ok                                                   
00:00:04|[prc] Success to init module!                                         
00:00:04|[pdc]                                                                 
                                                                               
PDC Build on Aug 19 2014 at 17:21:03.                                           
00:00:04|[pdc] SVN NUM: 4564.                                                   
                                                                               
00:00:04|[pdc] BASE_LINE: 210                                                   
00:00:04|[pdc] OSA_kProcCreate OK                                               
00:00:04|[OSA-DRV] Char device create OK !                                     
00:00:04|[pdc] PDC_PartionInit ok!!                                             
00:00:04|[pdc] HWID : IPC-HDW1100S:01:02:04:1D:0E:00:01:00:00:00:00:190:00:00:00
00:00:04|[OSA-DRV] Char device create OK !                                     
00:00:04|[pdc] binderFlag: 0x3, funcap: 0x18538b,0x0,0x0,0x0                   
00:00:04|[OSA-DRV] recordTsk  Task   pid=515   tid=515                         
00:00:04|[pdc] SenCfg Match OK,pCfgParams->pCfg: bf2690bc                       
00:00:04|[pdc] PDC_PRODUCT_OWNER: 0                                             
00:00:04|[pdc] Find Product: IPC-HDW1100S.                                     
00:00:04|[pdc] wifi cut down 0                                                 
00:00:04|[pdc] sd cut down 1610612755                                           
00:00:04|[pdc] Config size 1428 !                                               
00:00:04|[pdc] SenCfgSize: 204 Bytes                                           
00:00:04|[pdc] Init spiBus2  Successed!                                         
00:00:04|[prc] WARN  : TheKernel: ssp initial ok!                               
 I2C0 has benn  created                                                         
00:00:04|[pdc] Init I2CBus0  Successed!                                         
00:00:04|[pdc] PDC_MODULE_RESET_STATE                                           
00:00:04|[pdc] Dev has No shutDown Cfg!                                         
00:00:04|[pdc] P***************AT88SC Crypt Version***************             
DC_pinInit As UsType: DH General. UserZone ReadOnly: false                     
ual!                                                                           
SVN: 2263                                                                       
00:00:04|[pdc] GBuilt in: Jun 24 2014 16:19:37                                 
et reset pin: 12**************************************************             
 OK !                                                                           
00:00:04|[pdc] ircut types = [0]                                               
00:00:04|[pdc] ircut types = [1]                                               
00:00:04|[pdc] ircut types = [2]                                               
00:00:04|[OSA-DRV] Char device create OK !                                     
00:00:04|[pdc] Get comPort Cfg ok !0sa                                         
00:00:04|[pdc] PDC_comInit OK!                                                 
00:00:04|[pdc] PDC_MODULE_SENSOR                                               
00:00:04|[pdc] Try RtcDev: SocRtc                                               
00:00:04|[pdc] phyaddr = 854ff000, memLen = 1000                               
00:00:04|[pdc] DDRdata crc incorrect, Load from sramFile                       
00:00:04|[pdc] phyaddr = 854ff000, memLen = 1000                               
00:00:04|[pdc] DDRdata crc incorrect, Load from sramFile                       
00:00:04|[pdc] A B OK                                                           
00:00:04|[pdc] Both of Chief and Backup File CRC check OK!                     
 00:00:04|[pdc] phyaddr = 854ff000, memLen = 1000                               
00:00:04|[pdc] DDRdata crc incorrecterror: write byte error                     
, Load from sramerror: write_nbytes failed                                     
File                                                                           
rror: verify_read_password failed, PAC = ffffffff                               
32m00:00:04|[pdcerror: authenticate failed                                     
] Both of Chief and Backup File CRC check OK!                                 
 00:00:04|[pdc] phyaddr = 854ff000, memLen = 1000                               
00:00:04|[pdc] Choose RtcType: 4 -> SocRtc                                     
00:00:04|[OSA-DRV] Char device create OK !                                     
00:00:04|[pdc] OSA_kProcAddFile:pdcRtc OK!                                     
Restarting system. 


00:00:04|[pdc] DDRdata crc incorrecterror: write byte error, Load from sramerror: write_nbytes failed

Возможно прошивки не подходят?

iTuneDVR
Сообщения: 3218
Зарегистрирован: 24 авг 2013, 11:05

Re: Восстановление IPC-HFW1100SP

Сообщение iTuneDVR » 11 мар 2016, 18:51

Камера чинайская?


Вернуться в «IPC DAHUA»