TIGRIS TI-VP2M

iTuneDVR
Сообщения: 3218
Зарегистрирован: 24 авг 2013, 11:05

TIGRIS TI-VP2M

Сообщение iTuneDVR » 11 мар 2016, 23:51

Попалась проблемная камера. Внешне никаких признаков. Внутренне - перезагрузка по кругу.
Камера на Ti платформе.
Прошивок пока нет.
Пока стопор.

Нащупал TTL подключился ;)

Изображение

Код: Выделить всё

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.03.05 00:16:02 =~=~=~=~=~=~=~=~=~=~=~=
DM36x initialization passed!
TI UBL Version: 1.50
Booting Catalog Boot Loader
BootMode = NAND
Starting NAND Copy...
Valid magicnum, 0xA1ACED66, found in block 0x00000019.
   DONE
Jumping to entry point at 0x81080000.


U-Boot 1.3.4 (Aug  9 2013 - 00:26:09)

I2C:   ready
DRAM:  128 MB
NETVIEW-1 NAND:  NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
128 MiB
In:    serial
Out:   serial
Err:   serial
link off

Ethernet PHY: INST36X @ 0x00
Hit any key to stop autoboot:  1  0
NETVIEW IPNC:>
NETVIEW IPNC:>
NETVIEW IPNC:>help
?       - alias for 'help'
askenv  - get environment variables from stdin
autoscr - run script from memory
base    - print or set address offset
boot    - boot default, i.e., run 'bootcmd'
bootd   - boot default, i.e., run 'bootcmd'
bootm   - boot application image from memory
bootp   - boot image via network using BootP/TFTP protocol
cmp    - memory compare
coninfo - print console devices and information
cp    - memory copy
crc32    - checksum calculation
dhcp   - invoke DHCP client to obtain IP/boot params
echo    - echo args to console
fsinfo   - print information about filesystems
fsload   - load binary file from a filesystem image
go      - start application at address 'addr'
help    - print online help
icrc32  - checksum calculation
iloop   - infinite loop on address range
imd     - i2c memory display
iminfo  - print header information for application image
imm     - i2c memory modify (auto-incrementing)
imw     - memory write (fill)
imxtract- extract a part of a multi-image
inm     - memory modify (constant address)
iprobe  - probe to discover valid I2C chip addresses
itest   - return true/false on integer compare
loadb   - load binary file over serial line (kermit mode)
loads   - load S-Record file over serial line
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
ls   - list files in a directory (default /)
md    - memory display
mii     - MII utility commands
mm    - memory modify (auto-incrementing)
mtest    - simple RAM test
mw    - memory write (fill)
nand - NAND sub-system
nboot   - boot from NAND device
nfs   - boot image via network using NFS protocol
nm    - memory modify (constant address)
ping   - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
saves   - save S-Record file over serial line
setenv  - set environment variables
sleep   - delay execution for some time
tftpboot- boot image via network using TFTP protocol
version - print monitor version
NETVIEW IPNC:>
NETVIEW IPNC:>
NETVIEW IPNC:>
NETVIEW IPNC:>printenv
bootdelay=1
baudrate=115200
bootfile="uImage"
ethaddr=00:00:1b:00:00:11
filesize=19E2000
fileaddr=82000000
ipaddr=192.168.1.12
serverip=192.168.1.15
bootcmd=nboot 0x80700000 0 0x700000;bootm 0x80700000
bootargs=console=ttyS0,115200n8 noinitrd rw ip=192.168.1.134:192.168.1.1::::: root=/dev/mtdblock3 rw rootfstype=cramfs mem=48M eth=00:00:1b:00:00:11
stdin=serial
stdout=serial
stderr=serial
ver=U-Boot 1.3.4 (Aug  9 2013 - 00:26:09)

Environment size: 434/262140 bytes
NETVIEW IPNC:>





Код: Выделить всё

DM36x initialization passed!
TI UBL Version: 1.50
Booting Catalog Boot Loader
BootMode = NAND
Starting NAND Copy...
Valid magicnum, 0xA1ACED66, found in block 0x00000019.
   DONE
Jumping to entry point at 0x81080000.


U-Boot 1.3.4 (Aug  9 2013 - 00:26:09)

I2C:   ready
DRAM:  128 MB
NETVIEW-1 NAND:  NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
128 MiB
In:    serial
Out:   serial
Err:   serial
link off

Ethernet PHY: INST36X @ 0x00
Hit any key to stop autoboot:  1  0

Loading from NAND 128MiB 3,3V 8-bit, offset 0x700000
   Image Name:   Linux-2.6.18_pro500-davinci
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1840416 Bytes =  1.8 MB
   Load Address: 80008000
   Entry Point:  80008000
## Booting kernel from Legacy Image at 80700000 ...
   Image Name:   Linux-2.6.18_pro500-davinci
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1840416 Bytes =  1.8 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux........................................................................................................................... done, booting the kernel.
Linux version 2.6.18_pro500-davinci (root@ubuntu) (gcc 版本 4.2.0 (MontaVista 4.2.0-16.0.32.0801914 2008-08-30)) #1 PREEMPT Fri Jun 6 09:30:46 CST 2014
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: DaVinci DM368 IPNC
Memory policy: ECC disabled, Data cache writeback
DaVinci DM0365 variant 0x8
PLL0: fixedrate: 24000000, commonrate: 170000000, vpssrate: 340000000
PLL0: vencrate_sd: 75555555, ddrrate: 340000000 mmcsdrate: 97142857
PLL1: armrate: 432000000, voicerate: 20571428, vencrate_hd: 27000000
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
Built 1 zonelists.  Total pages: 12288
Kernel command line: console=ttyS0,115200n8 noinitrd rw ip=192.168.1.134:192.168.1.1::::: root=/dev/mtdblock3 rw rootfstype=cramfs mem=48M eth=00:00:1b:00:00:11
TI DaVinci EMAC: kernel boot params Ethernet address: 00:00:1b:00:00:11
PID hash table entries: 256 (order: 8, 1024 bytes)
Clock event device timer0_0 configured with caps set: 07
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 48MB = 48MB total
Memory: 44672KB available (3149K code, 653K data, 180K init)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
DaVinci: 104 gpio irqs
MUX: initialized GPIO20
MUX: initialized I2C_SCL
MUX: initialized SD1_DATA1
MUX: initialized GPIO28
Generic PHY: Registered new driver
ch0 default output "COMPOSITE", mode "NTSC"
VPBE Encoder Initialized
SCSI subsystem initialized
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered


 ***davinci_spi_board_init()!<3>Pin SPI1_SCLK already used for SD1_DATA1.
MUX: initialized SPI1_SDO
spi1 register ret = 0 ~~~~~~~~~~~~~~~~~~~~~


 ***davinci_spi_board_init_End(0)!<5>VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.1 (2006/08/19) Phillip Lougher
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
yaffs Jun  6 2014 09:34:05 Installing.
SGI XFS with no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
LTT : ltt-facilities init
LTT : ltt-facility-core init in kernel
DAVINCI-WDT: DaVinci Watchdog Timer: heartbeat 60 sec
MUX: initialized PWM0
Pin PWM2_G87 already used for GPIO87.
MUX: initialized PWM3_G80
MUX: initialized PWM3_G81
MUX: initialized PWM3_G85
MUX: initialized PWM3_G86
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO map 0x1c20000 mem 0xfbc20000 (irq = 40) is a 16550A
serial8250.0: ttyS1 at MMIO map 0x1d06000 mem 0xfbd06000 (irq = 41) is a 16550A
RAMDISK driver initialized: 1 RAM disks of 32768K size 1024 blocksize
Davinci EMAC MII Bus: probed
MAC address is 00:00:1b:00:00:11
TI DaVinci EMAC Linux version updated 4.0
Linux video capture interface: v2.00
Trying to register davinci display video device.
layer=c05cc600,layer->video_dev=c05cc760
Trying to register davinci display video device.
layer=c05cc400,layer->video_dev=c05cc560
davinci_init:DaVinci V4L2 Display Driver V1.0 loaded
i2c /dev entries driver
nand_davinci nand_davinci.0: Using 4-bit hardware ECC
NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
Creating 6 MTD partitions on "nand_davinci.0":
0x00000000-0x00300000 : "bootloader"
0x00300000-0x00700000 : "params"
0x00700000-0x00a00000 : "kernel"
0x00a00000-0x02a00000 : "filesystem"
0x02a00000-0x02e00000 : "data1"
0x02e00000-0x08000000 : "data2"
nand_davinci nand_davinci.0: hardware revision: 2.3
MUX: initialized SPI0_SCLK
MUX: initialized SPI0_SDO)
dm_spi1.1: davinci SPI Controller driver at 0xc3865800 (irq = 43) use_dma=0
spidev_init @@@@@@@@@@@@@@@@@@@@@@@@
spidev_probe~~~~~~~~~~~~~~~~~~~~~~
spidev_init OK: 0
rtc_davinci_dm365 rtc_davinci_dm365.0: rtc intf: proc
rtc_davinci_dm365 rtc_davinci_dm365.0: rtc intf: dev (254:0)
rtc_davinci_dm365 rtc_davinci_dm365.0: rtc core: registered rtc_davinci_dm365 as rtc0
rtc wait time out !!!!!

Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).
ASoC version 0.13.1
CQ0093 Voice Codec 0.1
asoc: cq93vc <-> davinci-vcif mapping ok
ALSA device list:
  #0: On-chip voice codec (cq93vc)
IPv4 over IPv4 tunneling driver
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
rtc_davinci_dm365 rtc_davinci_dm365.0: setting the system clock to 2000-01-01 00:00:00 (946684800)
Time: timer0_1 clocksource has been installed.
Clock event device timer0_0 configured with caps set: 08
Switched to high resolution mode on CPU 0
IP-Config: Guessing netmask 255.255.255.0
IP-Config: Complete:
      device=eth0, addr=192.168.1.134, mask=255.255.255.0, gw=255.255.255.255,
     host=192.168.1.134, domain=, nis-domain=(none),
     bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=
VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 180K

INIT: version 2.86 booting


0
mkdir: Cannot create directory `/dev/.test': Read-only file system
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
0
CSL: Module install successful, device major num = 252
CSL: Module version 0.10.00, built on Jun 18 2014 14:55:05

I2C: Module install successful, device major num = 251
DMA: Module install successful, device major num = 250
DRV: Module install successful
DRV: Module built on Jun 18 2014 14:55:08
DRV: EDMACC.QUEPRI  = 00000777
DRV: SYSTEM.MSTPRI0 = 00440022
DRV: SYSTEM.MSTPRI1 = 00000244
DRV: ISP.BCR        = 00000002
DRV: SYSTEM.MISC    = 00000399
CMEMK module: built on Dec  3 2011 at 01:26:39
  Reference Linux version 2.6.18
  File /mnt/workdir/diskb/ipnc_ar0331/dvsdk_2_10_01_18/linuxutils_2_24_03/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c
allocated heap buffer 0xc4000000 of size 0x5000000
CMEM Range Overlaps Kernel Physical - allowing overlap
CMEM phys_start (0x1000) overlaps kernel (0x80000000 -> 0x83000000)
cmemk initialized
EDMAK module: built on Dec  3 2011 at 01:26:40
  Reference Linux version 2.6.18
  File /mnt/workdir/diskb/ipnc_ar0331/dvsdk_2_10_01_18/linuxutils_2_24_03/packages/ti/sdo/linuxutils/edma/src/module/edmak.c
IRQK module: built on Dec  3 2011 at 01:26:41
  Reference Linux version 2.6.18
  File /mnt/workdir/diskb/ipnc_ar0331/dvsdk_2_10_01_18/linuxutils_2_24_03/packages/ti/sdo/linuxutils/irq/src/module/irqk.c
irqk initialized

<K>dm365 adc driver successful!
yaffs: dev is 32505860 name is "mtdblock4"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.4, "mtdblock4"
yaffs_read_super: isCheckpointed 0
ln: /var/www/snap.jpg: File exists
Starting mounting local filesystems: mount none on /dev/shm type tmpfs (rw,size=5M)
none on /var/run type tmpfs (rw)
none on /tmp type tmpfs (rw,sync)
Creat queue id:0
queue id:0
FileMngThread created
Creat queue id:32769
queue id:32769
AlramThread created
Share memory init success
gPlatform = 1 ~~~~~~
Creat queue id:65538
queue id:65538
Setting up networking ...rm: unable to remove `/etc/network/run': Read-only file system
queue id:32769
Global value size:21832
MagicNum: 2593849357, MagicNumConfig: 2593849357
ReadGlobal: 0 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
MagicNum: 2593849357, MagicNumConfig: 2593849357
queue id:65538
Creat queue id:98307
queue id:98307
Starting hotplug subsystem:
Check_device_version : DEVICE VER = 1 !!
killall: phddns_c_demo: no process killed
rm: cannot remove `/mnt/nand/AcountLevel.txt': No such file or directory
rm: cannot remove `/mnt/nand/ConnectStatus.txt': No such file or directory
time.windows.com: Unknown host
/opt/ipnc/ntpclient -s -i 10 -h time.windows.com

ntpclient return 256.
@@@@@@@@@@@@@@@@@@@@StreamType: 1, VideoCombo: 4 ~~~~~~

CPU is DM368
+++++++++++++++++g_res2When720P: 4 ~~~~~~
6666666666666666666666666666666para_mpeg4cvalue/1000==2048
++++++++++++++++++++++++++++++++++++++++++++++++pSysInfo->lan_config.nFrameRate1====0
tConfig.nVideocodecmode: 3,  tConfig.nVideocodecres: 1 ~~~~~~~~~~~~~~~~~~~~~~~
CPU CurrentStatus is = 1
===========pConfig -> nVideocodecmode=3=========
./av_server.out DM368 PAL TI2A AEWB FLIPH FLIPV D1_D1 H264 2048000 CBR AUTO MJPEG 75 PORT 4567 6666 MENUOFF &



TIMEZONE DAYLIGHT DEBUG COMMAND: cp -f /usr/share/zoneinfo/Etc/GMT-8 /mnt/nand/localtime

ApproDrvInit: 7
Creat queue id:131076
queue id:131076
   pci     
   pci      [success]

AVSERVER UI: Initializing.
   usb     
Pinmux1: 0x4f801a
Pinmux2: 0x10da
Pinmux3: 0x635affff
Pinmux4: 0x5471d400
 
 CLK Hz,
 ARM   Hz =  432000000
 DDR   Hz =  340000000
 VPSS  Hz =  340000000
 IMCOP Hz =  340000000
 
 DRV LDC: GetConfig 0005 0x0

 [OSA_FILE ] Reading file [/mnt/nand/IMG_Paramset.bin] ... ERROR

IMAGE TUNE: Paramset File is not available..... Setting DEFAULT parameter

CONFIGURING AVSERVER FOR DM368 .....
queue id:65538
------------------- 720 , 576 ------------------------
sensor mode:2;fps:30;width:736;height:576;DRV_imgsOpen
sensor mode:2;fps:30;width:736;height:576;DRV_imgsOpen
 Sensor Mode Info,
 Width      =  936
 Height     =  612
 fps        =   30
 Bin Enable =    1
 
 Sensor Frame Timing Info,
 fps                  = 30
 t_frame (ns)         = 33333334.000000
 t_row   (ns)         = 28687.500000
 t_pclk  (ns)         = 15.625000
 W                    = 936
 H                    = 612
 SW                   = 1125
 SD                   = 0
 HB                   = 450
 VB                   = 549
 HBmin                = 450
 VBmin                = 9
 f_pclk               = 64000000
 shutterOverhead (ns) = 6656.250000
 col_size             = 936
 row_size             = 612
 col_bin              = 0
 row_bin              = 0
 col_start            = 632
 row_start            = 540
 pll_M                = 16
 pll_N                = 1
 pll_DIV              = 1
 
############reset###########
############SET REG###########



 DRV_imgsSet50_60Hz is50Hz: 1 ~~~~~


TI Setting Applied
~~~~~~~ 736,576,736,576 ~~~~~~~~~~~~~~~~ 736,576,736,576 ~~~~~~~~~createPrm: width x height = 720 x 576, offsetH: 736, offsetV: 576 ~~~~~~~~~~~~~~~~~~~~
createPrm: width x height = 720 x 576, offsetH: 736, offsetV: 576 ~~~~~~~~~~~~~~~~~~~~
DavinciDisplay DavinciDisplay.1: Before finishing with S_FMT:
layer.pix_fmt.bytesperline = 640,
 layer.pix_fmt.width = 640,
 layer.pix_fmt.height = 480,
 layer.pix_fmt.sizeimage =460800


 FR : 0 usersDavinciDisplay DavinciDisplay.1: pixfmt->width = 640,
 layer->layer_info.config.line_length= 640
 registered from exsiting face album
EVM AUTO_IRIS = 0



***********   min_exp = 29  ************


ag(1250,10000), dg(1024,4096),mul(a:8.000000,d:4.000000)
 degree:1, step:0.121094, g:1552
ag:1250, dg:1271 ->  ag:1250, dg:1271
queue id:32769
shared memory size 4096
======================== shared memory id:262152
queue id:131076
[File: rs_rtsp.c      , Func: RTSP_ThrStart       , Line: 02571] :Info:
MODLE: RTSP RTSP_SvrCreate

[File: rs_rtsp.c      , Func: RTSP_ThrStart       , Line: 02577] :Info:
MODLE: RTSP RTSP_SvrThrStart

888888888888888888888888888888888888
[File: rs_phone.c     , Func: PHONE_ThrStart      , Line: 00746] :Info:
MODLE: PhonePHONE_SvrCreate

[File: rs_phone.c     , Func: PHONE_ThrStart      , Line: 00752] :Info:
MODLE: PhonePHONE_SvrThrStart

PHONE_SvrThrFxn
[File: rs_phone.c     , Func: PHONE_SvrThrFxn     , Line: 00562] :Dbg:
MODLE: PhoneRendezvous_meet .......

TI AWB PRODUCTION VERSION 1.0.0



***********   min_exp = 29  ************


ag(1250,10000), dg(1024,4096),mul(a:8.000000,d:4.000000)
 degree:1, step:0.121094, g:1552
ag:1250, dg:1271 ->  ag:1250, dg:1271
[File: rs_rtsp_base64.c, Func: RTSP_Media_Para_SetSeqBase64, Line: 00188] :Dbg:
MODLE: RtspBase64 chn:0 pSeqBase64 = Z2QAKK2EBUViuKxUdCAqKxXFYqOhAVFYrisVHQgKisVxWKjoQFRWK4rFR0ICorFcVio6ECSFITk8nyfk/k/J8nm5s00IEkKQnJ5Pk/J/J+T5PNzZprQFoJNKkAAAB4AAAcIGBAAH0AAACMoG974XhEI1
[File: rs_rtsp_base64.c, Func: RTSP_Media_Para_SetPictBase64, Line: 00212] :Dbg:
MODLE: RtspBase64 chn:0 pPictBase64 = aO48sA==

AV irismode=1
AV irisopen=0



***********   min_exp = 29  ************


ag(1250,10000), dg(1024,4096),mul(a:8.000000,d:4.000000)
 degree:128, step:0.121094, g:20776
ag:10000, dg:2127 ->  ag:10000, dg:2127
ircutmode = 0
Night2Day = 1
ircuttime: 5, fps:25, frames:125
IrcutSwitchTime = 5
Video Lost 0
framerate1: 25 ~~~
SetFramerate1 25000
framerate2: 25 ~~~
SetFramerate2 25000
SetAudioInVolume 75 ~~~~~~@@@@@@@@@@
   usb      [success]
   isapnp 
Simple mixer control 'PGA',0
  Capabilities: cvolume
  Capture channels: Mono
  Limits: Capture 0 - 3
  Mono: Capture 2 [67%]
numid=2,iface=MIXER,name='Mono DAC Playback Volume'
  ; type=INTEGER,access=rw---,values=1,min=0,max=63,step=0
  : values=63
SetAudioOutVolume 100 ~~~~~~@@@@@@@@@@
SystemInit success
AddSysLog: (System is running now) ~~~
Schedule manager init success
   isapnp   [success]
   ide     
queue id:0
queue id:32769
route: SIOC[ADD|DEL]RT: File exists


------------------------------------
Onvif_server is running...
Platform:       TI
Console:       disable
Devname:       eth0
Webservice port:    8999
------------------------------------


   ide      [success]
   input   
   input    [success]
   scsi   
   scsi     [success]
done.
Starting portmap daemon: portmap
.
Starting internet superserver: inetd.io scheduler deadline registered

io scheduler cfq registered
 sbulla: unknown partition table
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
loop: loaded (max 8 devices)
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
CSLIP: code copyright 1989 Regents of the University of California
netconsole: not configured, aborting
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
davinci-mmc davinci-mmc.0: Supporting 4-bit mode
davinci-mmc davinci-mmc.0: Using DMA mode

killall: ntpclient: no process killed
UNABLE TO SYNC TO SNTP SERVER in 10 seconds
queue id:0
umount: /mnt/mmc: not mounted
SD Card insert 1 , isInit = 1 ~~~~~~~~~~
mount: special device /dev/mmcblk0 does not exist
mount: special device /dev/mmcblk0p1 does not exist
Error -1 fault: SOAP-ENV:Client [no subcode]
"End of file or no input: Operation interrupted or timed out (5 s recv delay) (5 s send delay)"
Detail: [no detail]
111111111111111111net_get_dns: file "/etc/resolv.conf" opened for reading error!

~~~~~~~~~~~~~~~~~~ StartNetwork   ~~~~~~~~~~~~~~~~~
@@@@@@@ dns==0.0.0.0,dns==0x0
cat: /etc/resolv.conf: No such file or directory
LocalIP="192.168.0.171"
NetMask="255.255.255.0"
Gateway="192.168.0.1"
DNS="192.168.0.1"
dhcp: 0 ~~~~~~~~~~~~~~~~~~~~
111111111#########################################
111111111@@@@@@@ ip==192.168.0.171
1111111111@@@@@@@ gateway==192.168.0.1
111111111111@@@@@@@ netmask==255.255.255.0
1111111111@@@@@@@ dns==192.168.0.1
dns=192.168.0.1
device: eth0
system_server/561[CPU#0]: BUG in local_bh_enable at kernel/softirq.c:196
watch_dog.c line 46shared memory size 4096
watch_dog.c line 49shared memory id:262152
========== create /var/run/watchdog.pid succeed....


CPU is DM368
Boa check platformId: 1 ~~
set_com_config tcsetattr sucsse
open /mnt/nand/ptz_control
: No such file or directory
open /mnt/nand/ptz_time_start_file
: No such file or directory
ApproDrvInit: 3
queue id:131076
queue id:0
queue id:32769
[01/Jan/2000:00:00:23 +0000] boa.c:365 - unable to bind: Address already in use

INIT: Entering runlevel: 3

Netview......danale p2p service...start...udwMid=40008 40020000 40020000 40020004 40020008
Netview......danale p2p service...weblanguage=9-1, MAC=00:00:1b:02:49:b6, serialnumber=VUMG9JA49I6AHXPR52
Netview......danale p2p service...Start..., __DAID__=VUMG9JA49I6AHXPR52, maxWaitMs=0
Netview......danale p2p InnovRingBuffer_Reset
In upnpDiscover........111
In upnpDiscover........112
In upnpDiscover........101
In upnpDiscover........001
In upnpDiscover........002
In upnpDiscover........003
In upnpDiscover........004
In upnpDiscover........007
In upnpDiscover........003
In upnpDiscover........004
In upnpDiscover........007
In upnpDiscover........003
In upnpDiscover........004
In upnpDiscover........007
In upnpDiscover........003
In upnpDiscover........004
In upnpDiscover........007
In upnpDiscover........102
In upnpDiscover........103
In upnpDiscover........104
In upnpDiscover........107
In upnpDiscover........114
In upnpDiscover........113
Sending M-SEARCH * HTTP/1.1

HOST: 239.255.255.250:1900

ST: urn:schemas-upnp-org:device:InternetGatewayDevice:1

MAN: "ssdp:discover"

MX: 3





MontaVista(R) Linux(R) Professional Edition 5.0.0 (0702774)



192.168.1.134 login: Error -1 fault: SOAP-ENV:Client [no subcode]
"End of file or no input: Operation interrupted or timed out (5 s recv delay) (5 s send delay)"
Detail: [no detail]


MontaVista(R) Linux(R) Professional Edition 5.0.0 (0702774)



192.168.1.134 login:

MontaVista(R) Linux(R) Professional Edition 5.0.0 (0702774)



192.168.1.134 login: Sending M-SEARCH * HTTP/1.1

HOST: 239.255.255.250:1900

ST: urn:schemas-upnp-org:service:WANIPConnection:1

MAN: "ssdp:discover"

MX: 3



admin
Password: Error -1 fault: SOAP-ENV:Client [no subcode]
"End of file or no input: Operation interrupted or timed out (5 s recv delay) (5 s send delay)"
Detail: [no detail]
Sending M-SEARCH * HTTP/1.1

HOST: 239.255.255.250:1900

ST: urn:schemas-upnp-org:service:WANPPPConnection:1

MAN: "ssdp:discover"

MX: 3





Sending M-SEARCH * HTTP/1.1

HOST: 239.255.255.250:1900

ST: upnp:rootdevice

MAN: "ssdp:discover"

MX: 3



M-SEARCH Reply:
ST: upnp:rootdevice
Location: http://192.0.0.128:2869/upnphost/udhisapi.dll?content=uuid:f12f88ae-364e-45e6-9549-852cb6fda03f
found device: http://192.0.0.128:2869/upnphost/udhisapi.dll?content=uuid:f12f88ae-364e-45e6-9549-852cb6fda03f
Netview......danale p2p service started
connected
Netview......StreamDispatchThrFxn recv [16] channel[0]
>>>>>>>>>>>> P2P started <<<<<<<<<<<<
Netview......StreamDispatchThrFxn recv buffer size[48]Hello-Innov
Login incorrect
192.168.1.134 login: 192.168.1.134 login: Error -1 fault: SOAP-ENV:Client [no subcode]
"End of file or no input: Operation interrupted or timed out (5 s recv delay) (5 s send delay)"
Detail: [no detail]
admin
Password:
Error -1 fault: SOAP-ENV:Client [no subcode]
"End of file or no input: Operation interrupted or timed out (5 s recv delay) (5 s send delay)"
Detail: [no detail]
Login incorrect
192.168.1.134 login: admin
Password: Error -1 fault: SOAP-ENV:Client [no subcode]
"End of file or no input: Operation interrupted or timed out (5 s recv delay) (5 s send delay)"
Detail: [no detail]

Login incorrect


MontaVista(R) Linux(R) Professional Edition 5.0.0 (0702774)



192.168.1.134 login: Error -1 fault: SOAP-ENV:Client [no subcode]
"End of file or no input: Operation interrupted or timed out (5 s recv delay) (5 s send delay)"
Detail: [no detail]


MontaVista(R) Linux(R) Professional Edition 5.0.0 (0702774)



192.168.1.134 login: root
Password:
Error -1 fault: SOAP-ENV:Client [no subcode]
"End of file or no input: Operation interrupted or timed out (5 s recv delay) (5 s send delay)"
Detail: [no detail]
Login incorrect
192.168.1.134 login: Error -1 fault: SOAP-ENV:Client [no subcode]
"End of file or no input: Operation interrupted or timed out (5 s recv delay) (5 s send delay)"
Detail: [no detail]
adminError -1 fault: SOAP-ENV:Client [no subcode]
"End of file or no input: Operation interrupted or timed out (5 s recv delay) (5 s send delay)"
Detail: [no detail]
lvjh
Password: Error -1 fault: SOAP-ENV:Client [no subcode]
"End of file or no input: Operation interrupted or timed out (5 s recv delay) (5 s send delay)"
Detail: [no detail]
=====reboot system now (boa)!!!!!11111
DM36x initialization passed!
TI UBL Version: 1.50
Booting Catalog Boot Loader
BootMode = NAND
Starting NAND Copy...
Valid magicnum, 0xA1ACED66, found in block 0x00000019.
   DONE
Jumping to entry point at 0x81080000.


U-Boot 1.3.4 (Aug  9 2013 - 00:26:09)

I2C:   ready
DRAM:  128 MB
NETVIEW-1 NAND:  NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit)
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
128 MiB
In:    serial
Out:   serial
Err:   serial
Ethernet PHY: INST36X @ 0x00
Hit any key to stop autoboot:  1  0
NETVIEW IPNC:>
NETVIEW IPNC:>
NETVIEW IPNC:>
NETVIEW IPNC:>


Альбом http://vk.com/album221982133_229778271

Вернуться в «IPC Longse»