3 трупа DVR3116H и DVR3104е

[iTuneDVR]

Читать нужно внимательно инструкцию и более того понимать, что означает каждое действие.

LIBDVR_TOOL: Appauto:0 dh_kb:0

К тому же надо читать инструкцию до конца, понимая, какие именно параметрам возвращаем исходные значения и за что они отвечают.

Я просил только включить логи загрузки.

[Kvintek]

так подскажите как включить =) я не против, обучится.
а про appauto странно возвращал обратно,
вот printenv

Код: Выделить всё

U-Boot 2010.06-svn502 (Oct 22 2012 - 12:43:11) svn:502

DRAM:  1 GiB
DM385-GP rev 1.0

N56_DVR Run at mode: C

dh_netmode: RMII
Net:   Ethernet clocking: 0x0
Detected MACID:90:d7:eb:c3:b8:66
cpsw
Hit any key to stop autoboot:  0
DVR> printenv

bootargs=mem=90M, console=ttyO0,115200n8 rootfstype=cramfs root=/dev/mtdblock1 earlyprintk notifyk.vpssm3_sva=0xbffd0000
bootcmd=netup; fsload 0x81000000 /boot/uImage; bootm
bootdelay=3
baudrate=115200
ethaddr=90:D7:EB:C3:B8:66
gatewayip=192.168.1.1
netmask=255.255.255.0
load_modules=1
m3_print=1
watchdog=1
netup_timeout=3
logserver=127.0.0.1
da=tftp 0x81000000 u-boot.bin.img; flwrite
dr=tftp 0x81000000 romfs-x.cramfs.img; flwrite
du=tftp 0x81000000 user-x.cramfs.img; flwrite
dw=tftp 0x81000000 web-x.cramfs.img; flwrite
dl=tftp 0x81000000 logo-x.cramfs.img; flwrite
ds=tftp 0x81000000 slave-x.cramfs.img; flwrite
dc=tftp 0x81000000 custom-x.cramfs.img; flwrite
up=tftp 0x81000000 update.img; flwrite
tk=tftp 0x81000000 uImage; bootm
verify=yes
bootfile=/boot/uImage
loadaddr=0x81000000
tu=tftp 0x81000000 u-boot.bin; go 0x81000000
ethact=cpsw
ID=52300026
serverip=192.168.1.10
ipaddr=192.168.1.211
appauto=1
dh_keyboard=1
stdin=serial
stdout=serial
stderr=serial

Environment size: 969/8188 bytes
DVR>


[iTuneDVR]

так подскажите как включить =) я не против, обучится.

Все подсказки чёрным по белому и русским языком в инструкции по восстановлению представлены.
Обучиться - этимология этого слова означает обучить себя, так во и и обучайте себя.
Ресурс исключительно мотивационный

appauto - должно быть в состоянии запуска
dh_keyboard - должно быть в состоянии трансляции лога

Тогда будет и запуск и лог. По моему это очевидно. А так есть запуск и нет лога запуска

[stasenko]

Добрый вечер. помогите мне пожалуйста восстановить Dahua 3108e .Подключался RS 232 к нему и при подаче питания в ncom тишина, тем самым пришел к выводу что умер загрузчик. микросхема памяти стоит s29gl128p10tfi02 фирмы spansion . Я так понимаю загрузчик надо залить в нее , но есть проблема, не могу понять к каким контактам надо подключить программатор чтобы залить прошивку. есть программатор 5 проводков и вот такой http://radioparty.ru/prog-avr/457-avr-prog-ft232rl. помогите ,если есть возможность...

[iTuneDVR]

Как правило спрашивают где взять то, чем чем шить, как именно и что дальше. Программаторов море и танцев с ними тоже не мало репертуаров.

[oleglevsha]

Я думаю, что программатор, по вашей ссылке не справится с NOR Flash, он сможет работать лишь с SPI.
вам нужен такой девайс, или дороже, в смысле помощнее )
http://www.willem-ua.com/forum/20-572-1

[stasenko]

да. Программатор по ссылке дорогой и наверно профессиональный. А есть ли вариант чуть по проще, который можно собрать самостоятельно...
В планах не имею шить памяти сотнями, ограничусь несколькими штуками или чуть побольше. Натолкните на подходящий вариант , если не сложно...

[Kvintek]

Вот лог. загрузки

Код: Выделить всё

Terminal log file
Date: 30.01.2017 - 9:21:26
-----------------------------------------------


U-Boot 2010.06-svn502 (Oct 22 2012 - 12:43:11) svn:502

DRAM:  1 GiB
DM385-GP rev 1.0

N56_DVR Run at mode: C

dh_netmode: RMII
Net:   Ethernet clocking: 0x0
Detected MACID:90:d7:eb:c3:b8:66
cpsw
Hit any key to stop autoboot:  3  2  1  0
link up on port 0, speed 100, full duplex
netup time out: 3
Timeout
SPI probe: 16384 KiB S25FL128P_64K at 0:0 is now current device
### CRAMFS loading '/boot/uImage' to 0x81000000
### CRAMFS load complete: 2392360 bytes loaded to 0x81000000
*  kernel: default image load address = 0x81000000
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   Linux-2.6.37
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2392296 Bytes = 2.3 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   kernel data at 0x81000040, len = 0x002480e8 (2392296)
   Loading Kernel Image ... OK
OK
   kernel loaded at 0x80008000, end = 0x802500e8

Starting kernel ... mem=120M, console=ttyO0,115200n8 rootfstype=cramfs root=/dev/mtdblock1 earlyprintk notifyk.vpssm3_sva=0xbffd0000 dh_keyboard=0 load_modules=1 m3_print=1 watchdog=1

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.37 (liu_xin@driver) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #288 Tue Nov 27 13:19:15 CST 2012, svn:1680
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: dm385evm
reserved size = 0 at 0x0
Memory policy: ECC disabled, Data cache writeback
OMAP chip is DM385 1.0
SRAM: Mapped pa 0x402f1000 to va 0xfe400000 size: 0xf000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 30480
Kernel command line: mem=120M, console=ttyO0,115200n8 rootfstype=cramfs root=/dev/mtdblock1 earlyprintk notifyk.vpssm3_sva=0xbffd0000 dh_keyboard=0 load_modules=1 m3_print=1 watchdog=1
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 120MB = 120MB total
Memory: 116688k/116688k available, 6192k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffa00000 - 0xffe00000   (   4 MB)
    vmalloc : 0xc8000000 - 0xf8000000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xc7800000   ( 120 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .init : 0xc0008000 - 0xc0038000   ( 192 kB)
      .text : 0xc0038000 - 0xc0477000   (4348 kB)
      .data : 0xc0478000 - 0xc04b4500   ( 242 kB)
SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:375
omap_hwmod: gpio3: softreset failed (waited 10000 usec)
omap_hwmod: gpio4: softreset failed (waited 10000 usec)
IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
Total of 128 interrupts on 1 active controller
GPMC revision 6.0
Trying to install interrupt handler for IRQ368
Trying to install interrupt handler for IRQ369
Trying to install interrupt handler for IRQ370
Trying to install interrupt handler for IRQ371
Trying to install interrupt handler for IRQ372
Trying to install interrupt handler for IRQ373
Trying to install interrupt handler for IRQ374
Trying to install type control for IRQ375
Trying to set irq flags for IRQ375
OMAP clockevent source: GPTIMER1 at 20000000 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
omap_voltage_early_init: voltage driver support not added
regulator: core version 0.5
regulator: dummy:
NET: Registered protocol family 16
omap_voltage_domain_lookup: Voltage driver init not yet happened.Faulting!
omap_voltage_add_dev: VDD specified does not exist!
OMAP GPIO hardware version 0.1
OMAP GPIO hardware version 0.1
OMAP GPIO hardware version 0.1
OMAP GPIO hardware version 0.1
omap_mux_init: Add partition: #1: core, flags: 4
omap_init_ahci  cpu_is_dm385
registered ti81xx_vpss device
registered ti81xx on-chip HDMI device
registered ti81xx_fb device
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
omap2_mcspi: probe of omap2_mcspi.3 failed with error -2
omap2_mcspi: probe of omap2_mcspi.4 failed with error -2
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USBSS revision 4ea2080b
Switching to clocksource gp timer
musb-hdrc: version 6.0, host, debug=0
musb-hdrc musb-hdrc.0: dma type: pio
MUSB controller-0 revision 4ea20800
usb2phy: computed values rxcalib(15)DACs(36 15 15)
usb2phy: override computed values rxcalib(15)DACs(14 14 16)
usb2phy_config: musb(0) rxcalib done, rxcalib read value 6f675d86
musb-hdrc musb-hdrc.0: MUSB HDRC host driver
musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.37 musb-hcd
usb usb1: SerialNumber: musb-hdrc.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
musb-hdrc musb-hdrc.0: USB Host mode controller at c801e000 using PIO, IRQ 18
musb-hdrc musb-hdrc.1: dma type: pio
MUSB controller-1 revision 4ea20800
usb2phy: computed values rxcalib(15)DACs(35 12 14)
usb2phy: override computed values rxcalib(15)DACs(14 11 15)
usb2phy_config: musb(1) rxcalib done, rxcalib read value 6f67577e
musb-hdrc musb-hdrc.1: MUSB HDRC host driver
musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: MUSB HDRC host driver
usb usb2: Manufacturer: Linux 2.6.37 musb-hcd
usb usb2: SerialNumber: musb-hdrc.1
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
musb-hdrc musb-hdrc.1: USB Host mode controller at c8022800 using PIO, IRQ 19
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
PMU: registered new PMU device of type 0
omap-iommu omap-iommu.0: ducati registered
omap-iommu omap-iommu.1: sys registered
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 227
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
omap_uart.0: ttyO0 at MMIO 0x48020000 (irq = 72) is a OMAP UART0
console [ttyO0] enabled
omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
brd: module loaded
loop: module loaded
ahci ahci.0: forcing PORTS_IMPL to 0x1
ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
scsi0 : ahci_platform
ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 16
ahci ahci.1: forcing PORTS_IMPL to 0x1
ahci ahci.1: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci.1: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
scsi1 : ahci_platform
ata2: SATA max UDMA/133 mmio [mem 0x4a0ae000-0x4a0befff] port 0x100 irq 59
m25p80 spi1.0: found s25sl12801, expected w25x32
m25p80 spi1.0: s25sl12801 (16384 Kbytes)
Creating 8 MTD partitions on "spi_flash":
0x000000000000-0x000000060000 : "boot"
0x000000060000-0x000000460000 : "rootfs"
0x000000460000-0x000000a60000 : "user"
0x000000a60000-0x000000c60000 : "web"
0x000000c60000-0x000000e60000 : "slave"
0x000000e60000-0x000000e80000 : "custom"
0x000000e80000-0x000000ec0000 : "logo"
0x000000ec0000-0x000001000000 : "config"
davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
davinci_mdio davinci_mdio.0: detected phy mask fffffffe
davinci_mdio.0: probed
davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown
davinci_mdio davinci_mdio.0: netcard_num = 1
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver dm9601
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
OMAP Watchdog Timer Rev 0x00: initial timeout 180 sec
OMAP Watchdog is enabled!
start WDT check timer.
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
notify_init : notify drivercreated  for  remote proc id 2 at physical Address 0xbffd0000
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
omap_voltage_late_init: Voltage driver support not added
Power Management for TI81XX.
Detected MACID=90:d7:eb:c3:b8:66
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
ata2: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-9: ST2000DM001-1ER164, CC26, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      ST2000DM001-1ER1 CC26 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
 sda: unknown partition table
sd 0:0:0:0: [sda] Attached SCSI disk
VFS: Mounted root (cramfs filesystem) readonly on device 31:1.
devtmpfs: mounted
Freeing init memory: 192K

UNRAR 3.93 freeware      Copyright (c) 1993-2010 Alexander Roshal


Extracting from /slave/dvr_rdk_fw_m3video.rar

Extracting  /var/dvr_rdk_fw_m3video.xem3                                   3%  6% 10% 13% 16% 20% 23% 26% 30% 33% 36% 40% 43% 46% 50% 53% 57% 60% 63% 67% 70% 73% 77% 80% 83% 87% 90% 93% 97% 99%  OK
All OK

UNRAR 3.93 freeware      Copyright (c) 1993-2010 Alexander Roshal


Extracting from /slave/dvr_rdk_fw_m3vpss.rar

Extracting  /var/dvr_rdk_fw_m3vpss.xem3                                    4%  9% 14% 19% 23% 28% 33% 38% 43% 47% 52% 57% 62% 67% 71% 76% 81% 86% 91% 95% 99%  OK
All OK
Attached to slave procId 2.
Loaded file /var/dvr_rdk_fw_m3vpss.xem3 on slave procId 2.
Started slave procId 2.
After Ipc_loadcallback status [0x00000000]
After Ipc_startcallback status [0x097d2000]
Attached to slave procId 1.
Loaded file /var/dvr_rdk_fw_m3video.xem3 on slave procId 1.
Started slave procId 1.
After Ipc_loadcallback status [0x00000000]
After Ipc_startcallback status [0x00000000]
 [c6xdsp ] Remote Debug Shared Memory @ 0xbfff0000
 [m3video] Remote Debug Shared Memory @ 0xbfff5020
 [m3vpss ] Remote Debug Shared Memory @ 0xbfffa040
 [m3vpss ] Received character 's'
 [c6xdsp ] Remote Debug Shared Memory @ 0xbfff0000
 [m3video] Remote Debug Shared Memory @ 0xbfff5020
 [m3vpss ] Remote Debug Shared Memory @ 0xbfffa040
### CRAMFS load complete: 2392360 bytes loaded to 0x81000000
*  kernel: default image load address = 0x81000000
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   Linux-2.6.37
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2392296 Bytes = 2.3 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   kernel data at 0x81000040, len = 0x002480e8 (2392296)
   Loading Kernel Image ... OK
OK
   kernel loaded at 0x80008000, end = 0x802500e8

Starting kernel ... mem=120M, console=ttyO0,115200n8 rootfstype=cramfs root=/dev/mtdblock1 earlyprintk notifyk.vpssm3_sva=0xbffd0000 dh_keyboard=0 load_modules=1 m3_print=1 watchdog=1

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.37 (liu_xin@driver) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #288 Tue Nov 27 13:19:15 CST 2012, svn:1680
CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: dm385evm
reserved size = 0 at 0x0
Memory policy: ECC disabled, Data cache writeback
OMAP chip is DM385 1.0
SRAM: Mapped pa 0x402f1000 to va 0xfe400000 size: 0xf000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 30480
Kernel command line: mem=120M, console=ttyO0,115200n8 rootfstype=cramfs root=/dev/mtdblock1 earlyprintk notifyk.vpssm3_sva=0xbffd0000 dh_keyboard=0 load_modules=1 m3_print=1 watchdog=1
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 120MB = 120MB total
Memory: 116688k/116688k available, 6192k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffa00000 - 0xffe00000   (   4 MB)
    vmalloc : 0xc8000000 - 0xf8000000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xc7800000   ( 120 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .init : 0xc0008000 - 0xc0038000   ( 192 kB)
      .text : 0xc0038000 - 0xc0477000   (4348 kB)
      .data : 0xc0478000 - 0xc04b4500   ( 242 kB)
SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:375
omap_hwmod: gpio3: softreset failed (waited 10000 usec)
omap_hwmod: gpio4: softreset failed (waited 10000 usec)
IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
Total of 128 interrupts on 1 active controller
GPMC revision 6.0
Trying to install interrupt handler for IRQ368
Trying to install interrupt handler for IRQ369
Trying to install interrupt handler for IRQ370
Trying to install interrupt handler for IRQ371
Trying to install interrupt handler for IRQ372
Trying to install interrupt handler for IRQ373
Trying to install interrupt handler for IRQ374
Trying to install type control for IRQ375
Trying to set irq flags for IRQ375
OMAP clockevent source: GPTIMER1 at 20000000 Hz
Console: colour dummy device 80x30
Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
devtmpfs: initialized
omap_voltage_early_init: voltage driver support not added
regulator: core version 0.5
regulator: dummy:
NET: Registered protocol family 16
omap_voltage_domain_lookup: Voltage driver init not yet happened.Faulting!
omap_voltage_add_dev: VDD specified does not exist!
OMAP GPIO hardware version 0.1
OMAP GPIO hardware version 0.1
OMAP GPIO hardware version 0.1
OMAP GPIO hardware version 0.1
omap_mux_init: Add partition: #1: core, flags: 4
omap_init_ahci  cpu_is_dm385
registered ti81xx_vpss device
registered ti81xx on-chip HDMI device
registered ti81xx_fb device
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
omap2_mcspi: probe of omap2_mcspi.3 failed with error -2
omap2_mcspi: probe of omap2_mcspi.4 failed with error -2
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USBSS revision 4ea2080b
Switching to clocksource gp timer
musb-hdrc: version 6.0, host, debug=0
musb-hdrc musb-hdrc.0: dma type: pio
MUSB controller-0 revision 4ea20800
usb2phy: computed values rxcalib(15)DACs(36 15 15)
usb2phy: override computed values rxcalib(15)DACs(14 14 16)
usb2phy_config: musb(0) rxcalib done, rxcalib read value 6f675d86
musb-hdrc musb-hdrc.0: MUSB HDRC host driver
musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.37 musb-hcd
usb usb1: SerialNumber: musb-hdrc.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
musb-hdrc musb-hdrc.0: USB Host mode controller at c801e000 using PIO, IRQ 18
musb-hdrc musb-hdrc.1: dma type: pio
MUSB controller-1 revision 4ea20800
usb2phy: computed values rxcalib(15)DACs(35 12 14)
usb2phy: override computed values rxcalib(15)DACs(14 11 15)
usb2phy_config: musb(1) rxcalib done, rxcalib read value 6f67577e
musb-hdrc musb-hdrc.1: MUSB HDRC host driver
musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: MUSB HDRC host driver
usb usb2: Manufacturer: Linux 2.6.37 musb-hcd
usb usb2: SerialNumber: musb-hdrc.1
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
musb-hdrc musb-hdrc.1: USB Host mode controller at c8022800 using PIO, IRQ 19
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
PMU: registered new PMU device of type 0
omap-iommu omap-iommu.0: ducati registered
omap-iommu omap-iommu.1: sys registered
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 227
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
omap_uart.0: ttyO0 at MMIO 0x48020000 (irq = 72) is a OMAP UART0
console [ttyO0] enabled
omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
brd: module loaded
loop: module loaded
ahci ahci.0: forcing PORTS_IMPL to 0x1
ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
scsi0 : ahci_platform
ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 16
ahci ahci.1: forcing PORTS_IMPL to 0x1
ahci ahci.1: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
ahci ahci.1: flags: ncq sntf pm led clo only pmp pio slum part ccc apst
scsi1 : ahci_platform
ata2: SATA max UDMA/133 mmio [mem 0x4a0ae000-0x4a0befff] port 0x100 irq 59
m25p80 spi1.0: found s25sl12801, expected w25x32
m25p80 spi1.0: s25sl12801 (16384 Kbytes)
Creating 8 MTD partitions on "spi_flash":
0x000000000000-0x000000060000 : "boot"
0x000000060000-0x000000460000 : "rootfs"
0x000000460000-0x000000a60000 : "user"
0x000000a60000-0x000000c60000 : "web"
0x000000c60000-0x000000e60000 : "slave"
0x000000e60000-0x000000e80000 : "custom"
0x000000e80000-0x000000ec0000 : "logo"
0x000000ec0000-0x000001000000 : "config"
davinci_mdio davinci_mdio.0: davinci mdio revision 1.6
davinci_mdio davinci_mdio.0: detected phy mask fffffffe
davinci_mdio.0: probed
davinci_mdio davinci_mdio.0: phy[0]: device 0:00, driver unknown
davinci_mdio davinci_mdio.0: netcard_num = 1
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver dm9601
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
OMAP Watchdog Timer Rev 0x00: initial timeout 180 sec
OMAP Watchdog is enabled!
start WDT check timer.
usb 2-1: new low speed USB device using musb-hdrc and address 2
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
notify_init : notify drivercreated  for  remote proc id 2 at physical Address 0xbffd0000
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
omap_voltage_late_init: Voltage driver support not added
Power Management for TI81XX.
Detected MACID=90:d7:eb:c3:b8:66
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
ata2: SATA link down (SStatus 0 SControl 300)
usb 2-1: New USB device found, idVendor=1c4f, idProduct=0034
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: Usb Mouse
usb 2-1: Manufacturer: SIGMACHIP
input: SIGMACHIP Usb Mouse as /devices/platform/omap/ti81xx-usbss/musb-hdrc.1/usb2/2-1/2-1:1.0/input/input0
generic-usb 0003:1C4F:0034.0001: input: USB HID v1.10 Mouse [SIGMACHIP Usb Mouse] on usb-musb-hdrc.1-1/input0
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-9: ST2000DM001-1ER164, CC26, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      ST2000DM001-1ER1 CC26 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sda] 4096-byte physical blocks
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
 sda: unknown partition table
sd 0:0:0:0: [sda] Attached SCSI disk
VFS: Mounted root (cramfs filesystem) readonly on device 31:1.
devtmpfs: mounted
Freeing init memory: 192K

UNRAR 3.93 freeware      Copyright (c) 1993-2010 Alexander Roshal


Extracting from /slave/dvr_rdk_fw_m3video.rar

Extracting  /var/dvr_rdk_fw_m3video.xem3                                   3%  6% 10% 13% 16% 20% 23% 26% 30% 33% 36% 40% 43% 46% 50% 53% 57% 60% 63% 67% 70% 73% 77% 80% 83% 87% 90% 93% 97%usb 2-1: USB disconnect, address 2
 99%  OK
All OK

UNRAR 3.93 freeware      Copyright (c) 1993-2010 Alexander Roshal


Extracting from /slave/dvr_rdk_fw_m3vpss.rar

Extracting  /var/dvr_rdk_fw_m3vpss.xem3                                    4%  9% 14% 19% 23% 28% 33% 38% 43%usb 2-1: new low speed USB device using musb-hdrc and address 3
 47% 52% 57% 62% 67%usb 2-1: New USB device found, idVendor=1c4f, idProduct=0034
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: Usb Mouse
usb 2-1: Manufacturer: SIGMACHIP
 71%input: SIGMACHIP Usb Mouse as /devices/platform/omap/ti81xx-usbss/musb-hdrc.1/usb2/2-1/2-1:1.0/input/input1
generic-usb 0003:1C4F:0034.0002: input: USB HID v1.10 Mouse [SIGMACHIP Usb Mouse] on usb-musb-hdrc.1-1/input0
 76% 81% 86% 91% 95% 99%  OK
All OK
Attached to slave procId 2.
Loaded file /var/dvr_rdk_fw_m3vpss.xem3 on slave procId 2.
Started slave procId 2.
After Ipc_loadcallback status [0x00000000]
After Ipc_startcallback status [0x097d2000]
Attached to slave procId 1.
Loaded file /var/dvr_rdk_fw_m3video.xem3 on slave procId 1.
Started slave procId 1.
After Ipc_loadcallback status [0x00000000]
usb 2-1: USB disconnect, address 3
After Ipc_startcallback status [0x00000000]
 [c6xdsp ] Remote Debug Shared Memory @ 0xbfff0000
 [m3video] Remote Debug Shared Memory @ 0xbfff5020
 [m3vpss ] Remote Debug Shared Memory @ 0xbfffa040
 [m3vpss ] Received character 's'
 [c6xdsp ] Remote Debug Shared Memory @ 0xbfff0000
 [m3video] Remote Debug Shared Memory @ 0xbfff5020
 [m3vpss ] Remote Debug Shared Memory @ 0xbfffa040
 [m3video] Received character 's'
Config From File HDVideoOutPutFormat 4
~~~~~~~~~~~~~mode=hdmi:1280x1024@60~~get_outputformat 344

******************************************************************************
N56: vpss.ko Version: V1.02.02 Svn: 11425+ Compile at Sep 19 2012 17:03:05
******************************************************************************

******************************************************************************
N56: TI81xx_hdmi.ko Version: V1.02.01 Svn: 11425+ Compile at Sep 19 2012 17:03:09
******************************************************************************
HDMI W1 rev 4.0
I2C No Ack



******************************************************************************
N56: hdmiaudio.ko Version: V1.02.05 Svn: 11092+ Compile at Sep 18 2012 20:33:01
******************************************************************************
VPSS_DCTRL: venc 0 already stop
 
 ORG 0x46c00524: 0
 NEW 0x46c00524: 2
 
 
 ORG 0x46c009bc: 20
 NEW 0x46c009bc: 21
 
LIBDVR_TOOL: NetDeviceNum = 1
-----------------------------------------------------------------
SVN Version: 3014(Apr 11 2012 09:14:03)
Usage: netinit [ethname] [Ipaddress] [Netmask] [Gateway]
Example for set all(ip, netmask, gateway):
    netinit eth0 192.168.1.100 255.255.0.0 192.168.1.1
Example for set ip :
    netinit 192.168.1.34
Example for set netmask :
    netinit NULL 255.255.0.0(keep original ip)
-----------------------------------------------------------------
LIBDVR_TOOL: NetGetHostIPEx
LIBDVR_TOOL: NetGetGatewayEx
LIBDVR_TOOL: inet_addr(ip)
LIBDVR_TOOL: inet_addr(netmask)
LIBDVR_TOOL: inet_addr(gateway)
eth0
   LIBDVR_TOOL: NetSetHostIPEx(name, ip, netmask)
net eth0: PHY already attached
mac : 90-d7-eb-cnetinit uses obsolete (PF_INET,SOCK_PACKET)
3-b8-66
LIBDVR_TOOL: NetSetGatewayEx(name, gateway)
   ip : 192.168.1.211
   netmask : 255.255.255.0
   gateway : 192.168.1.1


UNRAR 3.93 freeware      Copyright (c) 1993-2010 Alexander Roshal


Extracting from /usr/bin/Challenge.rar

Extracting  /var/Challenge                                                 1%dvr_upnp_tv_ctrlpt_main 202 UPNP.PRO::CtrlPointStart
++++Start pppd,Version 1.42 2009-08-05+++
Name: upgraded, bulid date: Apr 25 2012 10:00:33, svn: 138
CtrlPointRefresh 464 UPNP.PRO::CtrlPointSearch
  2%  3%  4%  5%  6%  7%dvr_upnp_tv_ctrlpt_main 208 UPNP.PRO::success CtrlPointStart
  8%  9% 11% 12% 13% 14% 15% 16% 17% 18% 19% 21% 22% 23% 24% 25% 26% 27% 28% 29%PHY: 0:00 - Link is Up - 100/Full
 31% 32% 33% 34% 35% 36% 37% 38% 39% 41% 42% 43% 44% 45% 46% 47% 48% 49% 51% 52% 53% 54% 55% 56% 57% 58% 59% 61% 62% 63% 64% 65% 66% 67% 68% 69% 71% 72% 73% 74% 75% 76% 77% 78% 79% 81% 82% 83% 84% 85% 86% 87% 88% 89% 91% 92% 93% 94% 95% 96% 97% 98% 99%  OK
All OK
LIBDVR_TOOL: dvrhelper version: 3014(Apr 11 2012 09:14:03)
LIBDVR_TOOL: Appauto:0 dh_kb:0
Auto login as root ...
Jan  1 00:00:16 login[125]: root login on 'ttyO0'



BusyBox v1.18.4 (2012-04-25 13:44:14 CST) built-in shell (ash)
Platform: N56, Revision: 448
Enter 'help' for a list of built-in commands.

~ # CtrlPointAddDevice 976 Add New Device
CtrlPointAddDevice 1026 UPNP.PRO::Add a device

-----------------------------------------------
Date: 30.01.2017 - 9:25:24
End log file


[Kvintek]

я на правильном пути?
1. printenv
2.сменить параметры загрузки
set addauto 1 (Сменить на 0)
set dh_keyboard 1(Сменить на 0)
save
3. Задать адрес серверу TFTP (Локальный IP вашего ПК)
sip 192.168.1.10(пример)
Задать адрес клиента TFTP (IP адрес Регистратора)
lip 192.168.1.211 (Пример)
save
4. run dw

5. вернуть пареметры загрузки в исходное состояние
set addauto 1 (Сменить на 0)
set dh_keyboard 1(Сменить на 0)
save
единственное, что на команду ping 192.168.1.10 нет рекции,
а вот если писать run up то он успешно обновляет.

[iTuneDVR]

sip - адрес сервера TFTP
lip - адрес сетевого интерфейса на u-boot

Если есть подключение и маршрутизация, то всё должно работать.