Помогите определить принадлежность и отремонтировать

В этом разделе обсуждаются общие вопросы пользователей по теме IP камер, работы ПО.
GrukhvinEV
Сообщения: 40
Зарегистрирован: 11 мар 2017, 20:13

Помогите определить принадлежность и отремонтировать

Сообщение GrukhvinEV » 17 сен 2017, 01:23

Есть камера Falcon Eye FE-IPC-DL200P http://falconeye.su/Products/390/71/FE-IPC-DL200P/
С начала она начала перезагружаться и в один прекрасный момент пропала совсем.
Подключился к TTL получил следующее

Код: Выделить всё

U-Boot 2010.06.140517 (Aug 02 2014 - 15:17:40)

NAND:  Special Nand id table Version 1.35
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!
0 MiB
Check spi flash controller v350... Found
Spi(cs1) ID: 0xEF 0x40 0x18 0x00 0x00 0x00
Spi(cs1): Block:64KB Chip:16MB Name:"W25Q128B"
In:    serial
Out:   serial
Err:   serial
check reset gpio6_1 hold 0
Hit any key to stop autoboot:  0
Saving Environment to SPI Flash...
Erasing SPI flash, offset 0x00040000 size 64K ...done
Writing to SPI flash, offset 0x00040000 size 64K ...done
16384 KiB hi_sfc at 0:0 is now current device

## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Linux-3.0.8
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2505144 Bytes = 2.4 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 3.0.8 (root@sqy-desktop) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+uclibc_0.9.32.1+eabi+linuxpthread)) ) #5 Fri May 16 18:27:23 CST 2014
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: hi3518
Memory policy: ECC disabled, Data cache writeback
AXI bus clock 220000000.
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 22352
Kernel command line: mem=0x58M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfstype=cramfs mtdparts=hi_sfc:320K(uboot),2752K(kernel),3072K(rootfs),9472K(app),384K(config),384K(log) reset=0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 88MB = 88MB total
Memory: 82956k/82956k available, 7156k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0xc6000000 - 0xfe000000   ( 896 MB)
    lowmem  : 0xc0000000 - 0xc5800000   (  88 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc002a000   ( 136 kB)
      .text : 0xc002a000 - 0xc05e3000   (5860 kB)
      .data : 0xc05e4000 - 0xc060c9a0   ( 163 kB)
       .bss : 0xc060c9c4 - 0xc062a008   ( 118 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:32 nr_irqs:32 32
sched_clock: 32 bits at 110MHz, resolution 9ns, wraps every 39045ms
Console: colour dummy device 80x30
Calibrating delay loop... 218.72 BogoMIPS (lpj=1093632)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 5) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 5) is a PL011 rev2
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timer1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
NTFS driver 2.1.30 [Flags: R/W DEBUG].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.16)
msgmni has been set to 162
sqy test his lot is : 0x39  0x09  0x82  0x21  0x68  0x69  0x10  0x10
write command 0x03
verify r psw fail 0x03
encryption fail
encryption fail
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
loop: module loaded
Spi id table Version 1.22
Spi(cs1) ID: 0xEF 0x40 0x18 0x00 0x00 0x00
SPI FLASH start_up_mode is 3 Bytes
Spi(cs1):
Block:64KB
Chip:16MB
Name:"W25Q128B"
spi size: 16MB
chip num: 1
6 cmdlinepart partitions found on MTD device hi_sfc
Creating 6 MTD partitions on "hi_sfc":
0x000000000000-0x000000050000 : "uboot"
0x000000050000-0x000000300000 : "kernel"
0x000000300000-0x000000600000 : "rootfs"
0x000000600000-0x000000f40000 : "app"
0x000000f40000-0x000000fa0000 : "config"
0x000000fa0000-0x000001000000 : "log"
Special nand id table Version 1.35
Hisilicon Nand Flash Controller V301 Device Driver, Version 1.10
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found.
Fixed MDIO Bus: probed
himii: probed
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
usbcore: registered new interface driver rt2500usb
usbcore: registered new interface driver rt73usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 15, io mem 0x100b0000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
hiusb-ohci hiusb-ohci.0: irq 16, io mem 0x100a0000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver cdc_wdm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver mdc800
mdc800: v0.7.5 (30/10/2000):USB Driver for Mustek MDC800 Digital Camera
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
NET: Registered protocol family 17
NET: Registered protocol family 15
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
registered taskstats version 1
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
▒VFS: Mounted root (cramfs filesystem) readonly on device 31:2.
Freeing init memory: 136K

            _ _ _ _ _ _ _ _ _ _ _ _
            \  _  _   _  _ _ ___
            / /__/ \ |_/
           / __   /  -  _ ___
          / /  / /  / /
  _ _ _ _/ /  /  \_/  \_ ______
___________\___\__________________

[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
udevd (555): /proc/555/oom_adj is deprecated, please use /proc/555/oom_score_adj instead.
[RCS]: /etc/init.d/S80network
Auto login as root ...
Jan  1 00:00:05 login[560]: root login on 'ttyS000'
Welcome to HiLinux.
This app released with info
majorversion 1
minorversion 0
buildyear 2014
buildmonth 6
buildday 11
Login by /dev/ttyS000 at Thu Jan  1 00:00:05 UTC 1970.
find partition app index=3 addr=6291456 size=9699328
[uboot]partsize=327680
[kernel]partsize=2818048
[rootfs]partsize=3145728
[app]partsize=9699328
find partition app index=3 addr=6291456 size=9699328
18944+0 records in
18944+0 records out
9699328 bytes (9.3MB) copied, 2.530241 seconds, 3.7MB/s
[uboot]partsize=327680
[kernel]partsize=2818048
[rootfs]partsize=3145728
[app]partsize=9699328
[config]partsize=393216
find partition config index=4 addr=15990784 size=393216
[uboot]partsize=327680
[kernel]partsize=2818048
[rootfs]partsize=3145728
[app]partsize=9699328
[config]partsize=393216
[log]partsize=393216
find partition log index=5 addr=16384000 size=393216
insmod mmz.ko mmz=anonymous,0,0x85800000,168M anony=1 || report_error;
Hisilicon Media Memory Zone Manager
hi3518_base: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Hisilicon UMAP device driver interface: v3.00
pa:85800000, va:c7040000
load sys.ko for Hi3518...OK!
load viu.ko for Hi3518...OK!
ISP Mod init!
load vpss.ko ....OK!
load vou.ko ....OK!
[2]+  Done                       ./appinstall
# load venc.ko for Hi3518...OK!
load group.ko for Hi3518...OK!
load chnl.ko for Hi3518...OK!
load h264e.ko for Hi3518...OK!
load jpege.ko for Hi3518...OK!
load rc.ko for Hi3518...OK!
load region.ko ....OK!
load vda.ko ....OK!
hi_i2c init is ok!
Kernel: ssp initial ok!
acodec inited!
insert audio
==== Your input Sensor type is imx122 ====
Starting up sysinit....
ifconfig eth0 192.168.1.110 netmask 255.255.255.0
ADDRCONF(NETDEV_UP): eth0: link is not ready
reseting mdio phy....
*** Board tools : ver0.0.1_20121120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x10091100: 0x00008143 --> 0x00000140
[END]
read [0x10091104]=0x3100
write [0x10091100]=0xb1002140
*** Board tools : ver0.0.1_20121120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x10091100: 0x00008140 --> 0xB1002140
[END]
*** Board tools : ver0.0.1_20121120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x10091100: 0xB100A140 --> 0x00000240
[END]
read [0x10091104]=0xffff
write [0x10091100]=0x17fff2240
*** Board tools : ver0.0.1_20121120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
[END]
fdisk: can't open '/dev/mmcblk0': No such file or directory
redeviding the storage....
fdisk: can't open '/dev/mmcblk0'
formatting the partition....
mke2fs 1.41.11 (14-Mar-2010)
Could not stat /dev/mmcblk0p1 --- No such file or directory

The device apparently does not exist; did you specify it correctly?
chmod: /usr/etc/var: No such file or directory
net.ipv4.tcp_keepalive_time = 60
net.ipv4.tcp_keepalive_probes = 4
net.ipv4.tcp_keepalive_intvl = 12
net.ipv4.tcp_retries2 = 7
Starting up app....0/1000
PHY: himii:01 - Link is Up - 100/Full
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[XMID][DBG][SnapMgr::SnapMgr(const char*):40] this=0x40164904: m_filePathRoot=/tmp/mmc/mmc1/snapshot
system:killall -9 ntpd;ntpd -l
killall: ntpd: no process killed
[MID][DBG][void* OnTimer_ms(void*):257] pid=1278 enter
[ANTS_Sys_InitDSPs.163.Info]ANTS_Sys_InitDSPs called : CurTime is 2017.08.31-17:28:32
[hal][Custom_Init:285] SensorModel content="IMX122"
[hal][Custom_Init:285] Customer content="DEFAULT"
[hal][Custom_Init:285] IsofDome content="n"
[hal][Custom_Init:285] IsofIr content="y"
[hal][Custom_Init:285] Hardware content="FSAN_HI3516C_D1404"
[hal][Custom_Init:285] Platform content="HI3516C"
[ANTS_Sys_InitDSPs.228.Info]**********************AUTHEN ************************!!!!!
open encry file fail
open encry file fail
[ANTS_Sys_InitDSPs.251.Error]Unknown Chip ID 0x17 0x40
[XMID][DBG][int ANTS_MID_Init(int):37] param=0x0
[XMID][DBG][CirBuffSlotMgr::CirBuffSlotMgr(unsigned int, unsigned int):36] this=0xf460a0: m_cirBuffSlotList=0xf460a0
[XMID][DBG][SignalerMgr::SignalerMgr():25] this=0xf460e0: m_SignalerList=0xf460e4
[XMID][DBG][CirBuff::CirBuff():22] this=0xf460a0: m_handleList=0xf4610c m_cirBuffMgr=0xf460a0 m_signalerMgr=0xf460e0
[XMID][DBG][EventBuff::EventBuff():70] this=0xf460a0: m_cirBuff=0xf460a0 m_cirBuffAccess=0xf46114
[XMID][DBG][void Pthread::Print():64] <Pthread m_threadName=int CirBuffSlotMgr::Create() m_threadFunc=0x401559d0 m_threadId=0x419364c0 />
[XMID][DBG][void List<T>::Print() [with T = unsigned int]:276] [0] *0xf46b58={link={0xf4610c, 0xf4610c}, slot=0xf47ce8}
[XMID][DBG][void Pthread::Print():64] <Pthread m_threadName=int EventBuff::Init() m_threadFunc=0x4015444c m_threadId=0x421d84c0 />
[ANTS_Sys_RegisterEventCallback.1567.Error]ANTS_Sys_RegisterEventCallback : SDK Not Init
[XMID][DBG][int ANTS_MID_Init(int):41] ANTS_MID_EVENT_Init ret = -1
[XMID][DBG][static void* CirBuffSlotMgr::MgrRecycleThread(void*):305] pid=1279 enter
[XMID][DBG][static void* EventBuff::MonitorBuffThreadFunc(void*):400] pid=1280 enter
[ANTS_Sys_RegisterEventCallback.1567.Error]ANTS_Sys_RegisterEventCallback : SDK Not Init
[XMID][DBG][int ANTS_MID_Init(int):41] ANTS_MID_EVENT_Init ret = -1
[ANTS_Sys_RegisterEventCallback.1567.Error]ANTS_Sys_RegisterEventCallback : SDK Not Init
[XMID][DBG][int ANTS_MID_Init(int):41] ANTS_MID_EVENT_Init ret = -1
[ANTS_Sys_RegisterEventCallback.1567.Error]ANTS_Sys_RegisterEventCallback : SDK Not Init
[XMID][DBG][int ANTS_MID_Init(int):41] ANTS_MID_EVENT_Init ret = -1
[ANTS_Sys_RegisterEventCallback.1567.Error]ANTS_Sys_RegisterEventCallback : SDK Not Init
[XMID][DBG][int ANTS_MID_Init(int):41] ANTS_MID_EVENT_Init ret = -1
[ANTS_Sys_RegisterEventCallback.1567.Error]ANTS_Sys_RegisterEventCallback : SDK Not Init
[XMID][DBG][int ANTS_MID_Init(int):41] ANTS_MID_EVENT_Init ret = -1
[ANTS_Sys_RegisterEventCallback.1567.Error]ANTS_Sys_RegisterEventCallback : SDK Not Init
[XMID][DBG][int ANTS_MID_Init(int):41] ANTS_MID_EVENT_Init ret = -1
[ANTS_Sys_RegisterEventCallback.1567.Error]ANTS_Sys_RegisterEventCallback : SDK Not Init
[XMID][DBG][int ANTS_MID_Init(int):41] ANTS_MID_EVENT_Init ret = -1
[ANTS_Sys_RegisterEventCallback.1567.Error]ANTS_Sys_RegisterEventCallback : SDK Not Init
[XMID][DBG][int ANTS_MID_Init(int):41] ANTS_MID_EVENT_Init ret = -1
[ANTS_Sys_RegisterEventCallback.1567.Error]ANTS_Sys_RegisterEventCallback : SDK Not Init
[XMID][DBG][int ANTS_MID_Init(int):41] ANTS_MID_EVENT_Init ret = -1
***link down status changed***.
PHY: himii:01 - Link is Down
PHY: himii:01 - Link is Up - 100/Full

Окружение

Код: Выделить всё

U-Boot 2010.06.140517 (Aug 02 2014 - 15:17:40)

NAND:  Special Nand id table Version 1.35
Nand ID: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
No NAND device found!!!
0 MiB
Check spi flash controller v350... Found
Spi(cs1) ID: 0xEF 0x40 0x18 0x00 0x00 0x00
Spi(cs1): Block:64KB Chip:16MB Name:"W25Q128B"
In:    serial
Out:   serial
Err:   serial
check reset gpio6_1 hold 0
Hit any key to stop autoboot:  0
hisilicon # printenv
bootcmd=sf probe 0;sf read 0x82000000 0x50000 0x2b0000;bootm 0x82000000
bootdelay=1
baudrate=115200
ethaddr=00:00:23:34:45:66
ipaddr=192.168.100.101
serverip=192.168.100.100
update_enable=n
update_partition=0123456789abcdef
cntfail=0
latefail=0
errk=0
errr=0
erra=0
netmask=255.255.255.0
bootfile="uImage"
update_postfix=.bin.hi3516c
resetpin=61
resetidle=1
resettime=050
cntboot=4
stampb=441114054467
stdin=serial
stdout=serial
stderr=serial
verify=n
update_result=0-NotEnable
bootargs=mem=0x58M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfstype=cramfs mtdparts=hi_sfc:320K(uboot),2752K(kernel),3072K(rootfs),9472K(app),384K(config),384K(log) reset=0
ver=U-Boot 2010.06.140517 (Aug 02 2014 - 15:17:40)

Environment size: 707/65532 bytes
hisilicon #

По tftp слил прошивку, все работает. Зашел через telnet все работает логин root пароль antslq
Ни одна программа не видит камеру, через веб интерфес тоже не заходит....
В линуксе особо не понимаю, но вот сделал следующее, мб поможет понять в чем проблема:

Код: Выделить всё

# ps
  PID USER       VSZ STAT COMMAND
    1 root      1708 S    init
    2 root         0 SW   [kthreadd]
    3 root         0 SW   [ksoftirqd/0]
    4 root         0 SW   [kworker/0:0]
    5 root         0 SW   [kworker/u:0]
    6 root         0 SW   [rcu_kthread]
    7 root         0 SW<  [khelper]
    8 root         0 SW   [kworker/u:1]
  146 root         0 SW   [sync_supers]
  148 root         0 SW   [bdi-default]
  149 root         0 SW<  [kintegrityd]
  151 root         0 SW<  [kblockd]
  164 root         0 SW   [khubd]
  177 root         0 SW<  [cfg80211]
  178 root         0 SW   [kworker/0:1]
  260 root         0 SW<  [rpciod]
  263 root         0 SW   [kswapd0]
  317 root         0 SW   [fsnotify_mark]
  334 root         0 SW<  [nfsiod]
  344 root         0 SW<  [crypto]
  422 root         0 SW   [mtdblock0]
  427 root         0 SW   [mtdblock1]
  432 root         0 SW   [mtdblock2]
  437 root         0 SW   [mtdblock3]
  442 root         0 SW   [mtdblock4]
  447 root         0 SW   [mtdblock5]
  452 root         0 SW   [romblock0]
  455 root         0 SW   [romblock1]
  458 root         0 SW   [romblock2]
  461 root         0 SW   [romblock3]
  464 root         0 SW   [romblock4]
  467 root         0 SW   [romblock5]
  517 root         0 SW<  [kpsmoused]
  526 root         0 SW   [kworker/u:2]
  555 root       872 S <  udevd --daemon
  560 root      1724 S    -sh
  635 root      1704 S    /bin/sh /etc/failsave
  637 root      1700 S    sleep 60
  638 root         0 SWN  [jffs2_gcd_mtd3]
  716 root         0 SW   [romblock6]
  721 root         0 SW   [mtdblock6]
  727 root         0 SW   [flush-31:6]
  729 root         0 SWN  [jffs2_gcd_mtd6]
  731 root      1752 S    /bin/sh ./appinstall
  821 root         0 SWN  [jffs2_gcd_mtd4]
  930 root         0 SWN  [jffs2_gcd_mtd5]
 1178 root      1072 S    sysinit
 1214 root      1704 S    telnetd
 1268 root      1704 S    syslogd -O /tmp/syslog.log -s 64 -b 8
 1272 root     39424 S    ./AntsOnvifServer
 1277 root      1704 S    ntpd -l
 1281 root      1708 R    ps
#
# find partition config index=4 addr=15990784 size=393216

Код: Выделить всё

 ip address
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000
    link/ether aa:ac:ae:8e:ec:04 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.110/24 brd 192.168.1.255 scope global eth0
    inet6 fe80::a8ac:aeff:fe8e:ec04/64 scope link
       valid_lft forever preferred_lft forever
[1]+  Done                       /etc/failsave
#

Код: Выделить всё

# netstat
Active Internet connections (w/o servers)
Proto Recv-Q Send-Q Local Address           Foreign Address         State
Active UNIX domain sockets (w/o servers)
Proto RefCnt Flags       Type       State         I-Node Path
unix  3      [ ]         DGRAM                      1330 /dev/log
unix  2      [ ]         DGRAM                       147 @/org/kernel/udev/udevd
unix  2      [ ]         DGRAM                      1409
#
Вложения
2.jpg
1.jpg

iTuneDVR
Сообщения: 3218
Зарегистрирован: 24 авг 2013, 11:05

Re: Помогите определить принадлежность и отремонтировать

Сообщение iTuneDVR » 17 сен 2017, 01:45

GrukhvinEV писал(а):По tftp слил прошивку, все работает. Зашел через telnet все работает логин root пароль antslq
Ни одна программа не видит камеру, через веб интерфес тоже не заходит....

По паролю все ясно, что это за производитель.

GrukhvinEV писал(а):

Код: Выделить всё

# netstat
Active Internet connections (w/o servers)
Proto Recv-Q Send-Q Local Address           Foreign Address         State
Active UNIX domain sockets (w/o servers)
Proto RefCnt Flags       Type       State         I-Node Path
unix  3      [ ]         DGRAM                      1330 /dev/log
unix  2      [ ]         DGRAM                       147 @/org/kernel/udev/udevd
unix  2      [ ]         DGRAM                      1409
#


Стоит попробовать

Код: Выделить всё

netstat -putan

для больших поробностей

iTuneDVR
Сообщения: 3218
Зарегистрирован: 24 авг 2013, 11:05

Re: Помогите определить принадлежность и отремонтировать

Сообщение iTuneDVR » 17 сен 2017, 01:56

Файловая сама в порядке т.к. она в режиме чтения и если что-то побилось, то на JFFS2 разделах т.к. он в режиме чтения-запись.

Сделать вывод


Пока была доступна камера, какая стояла прошивка и пробовалось с ней что-то делать, обновлять прошивку штатно, ту, что на сайте у фалкона приведена?

GrukhvinEV
Сообщения: 40
Зарегистрирован: 11 мар 2017, 20:13

Re: Помогите определить принадлежность и отремонтировать

Сообщение GrukhvinEV » 17 сен 2017, 02:18

Никто не признается по поводу прошивали ее или нет, думаю что все таки не трогали.

Код: Выделить всё

# mount
rootfs on / type rootfs (rw)
/dev/root on / type cramfs (ro,relatime)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
tmpfs on /dev type tmpfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,mode=600,ptmxmode=000)
/dev/mtdblock3 on /update type jffs2 (rw,relatime)
/dev/mtdblock6 on /root type jffs2 (rw,relatime)
usbfs on /proc/bus/usb type usbfs (rw,relatime)
/dev/mtdblock4 on /usr/etc type jffs2 (rw,relatime)
/dev/mtdblock5 on /root/log type jffs2 (rw,relatime)
none on /tmp type tmpfs (rw,relatime,size=16384k)
none on /var type tmpfs (rw,relatime,size=4096k)
#

iTuneDVR
Сообщения: 3218
Зарегистрирован: 24 авг 2013, 11:05

Re: Помогите определить принадлежность и отремонтировать

Сообщение iTuneDVR » 17 сен 2017, 02:33

Да, бывает и такое.

Дать команду


внимательно посмотреть на разделы примонтированным вот к этим точкам

Код: Выделить всё

/dev/mtdblock4 on /usr/etc type jffs2 (rw,relatime)
/dev/mtdblock5 on /root/log type jffs2 (rw,relatime)
/dev/mtdblock6 on /root type jffs2 (rw,relatime)

GrukhvinEV
Сообщения: 40
Зарегистрирован: 11 мар 2017, 20:13

Re: Помогите определить принадлежность и отремонтировать

Сообщение GrukhvinEV » 17 сен 2017, 06:21

Код: Выделить всё

# df
Filesystem           1K-blocks      Used Available Use% Mounted on
/dev/root                 5892      5892         0 100% /
tmpfs                    41544         4     41540   0% /dev
/dev/mtdblock3            9472      7000      2472  74% /update
/dev/mtdblock6           14592      7068      7524  48% /root
/dev/mtdblock4             384       280       104  73% /usr/etc
/dev/mtdblock5             384       248       136  65% /root/log
none                     16384         4     16380   0% /tmp
none                      4096         4      4092   0% /var
# find partition config index=4 addr=15990784 size=393216


Вот мб еще это поможет:

Код: Выделить всё

# ls -l
-rwxr-xr-x    1 1001     root       1270112 Sep 22  2014 AntsOnvifServer
-rwxr-xr-x    1 1001     root         10525 Sep 10  2014 appinstall
drwxr-xr-x    2 1001     root             0 Sep 13  2014 bin
drwxr-xr-x    2 1001     root             0 May 27  2014 ddns_libs
drwxr-xr-x    2 1001     root             0 Sep 22  2014 ext_libs
drwxr-xr-x    2 1001     root             0 Sep 22  2014 host_libs
drwxr-xr-x    2 1001     root             0 Mar 26  2014 lib
-rwxr-xr-x    1 1001     root          7259 Aug 22  2014 load3518
drwxr-xr-x    4 root     root             0 Jan  1  1970 log
drwxr-xr-x    2 1001     root             0 May 10  2014 protocol
drwxr-xr-x    3 1001     root             0 Sep 17 01:18 res_xml
-rw-r--r--    1 1001     root           120 Sep 30  2014 version
-rw-r--r--    1 1001     root             0 Sep 22  2014 watch
drwxr-xr-x    3 1001     root             0 Sep 22  2014 web
#

iTuneDVR
Сообщения: 3218
Зарегистрирован: 24 авг 2013, 11:05

Re: Помогите определить принадлежность и отремонтировать

Сообщение iTuneDVR » 17 сен 2017, 13:27

Сделайте еще, то, что я просил выше

Код: Выделить всё

netstat -putan

Если будет ругаться, то вначале netstat --help и посмотрите ключи, которых нет, чтобы их исключить.
Будут засвечены порты, которые слушаются точно, ну а дальше будем думать.

GrukhvinEV
Сообщения: 40
Зарегистрирован: 11 мар 2017, 20:13

Re: Помогите определить принадлежность и отремонтировать

Сообщение GrukhvinEV » 17 сен 2017, 15:23

# netstat -putan
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name
tcp 0 0 :::23 :::* LISTEN 1213/telnetd
udp 0 0 :::123 :::* 1277/ntpd
#

iTuneDVR
Сообщения: 3218
Зарегистрирован: 24 авг 2013, 11:05

Re: Помогите определить принадлежность и отремонтировать

Сообщение iTuneDVR » 17 сен 2017, 19:58

Как-то жидковато!
При наличии запущенного, судя по выводу ps, основного процесса, или на этот момент его уже нет?

Если процесс есть, то попробовать его убить через kill, и перезапустить его.
Также можно аккуратно зачистить логи!

GrukhvinEV
Сообщения: 40
Зарегистрирован: 11 мар 2017, 20:13

Re: Помогите определить принадлежность и отремонтировать

Сообщение GrukhvinEV » 17 сен 2017, 20:58

Вот когда полностью все загрузилось есть следующие процессы:

Код: Выделить всё

# ps
  PID USER       VSZ STAT COMMAND
    1 root      1708 S    init
    2 root         0 SW   [kthreadd]
    3 root         0 SW   [ksoftirqd/0]
    4 root         0 SW   [kworker/0:0]
    5 root         0 SW   [kworker/u:0]
    6 root         0 SW   [rcu_kthread]
    7 root         0 SW<  [khelper]
    8 root         0 SW   [kworker/u:1]
  146 root         0 SW   [sync_supers]
  148 root         0 SW   [bdi-default]
  149 root         0 SW<  [kintegrityd]
  151 root         0 SW<  [kblockd]
  164 root         0 SW   [khubd]
  177 root         0 SW<  [cfg80211]
  178 root         0 SW   [kworker/0:1]
  260 root         0 SW<  [rpciod]
  263 root         0 SW   [kswapd0]
  317 root         0 SW   [fsnotify_mark]
  334 root         0 SW<  [nfsiod]
  344 root         0 SW<  [crypto]
  422 root         0 SW   [mtdblock0]
  427 root         0 SW   [mtdblock1]
  432 root         0 SW   [mtdblock2]
  437 root         0 SW   [mtdblock3]
  442 root         0 SW   [mtdblock4]
  447 root         0 SW   [mtdblock5]
  452 root         0 SW   [romblock0]
  455 root         0 SW   [romblock1]
  458 root         0 SW   [romblock2]
  461 root         0 SW   [romblock3]
  464 root         0 SW   [romblock4]
  467 root         0 SW   [romblock5]
  517 root         0 SW<  [kpsmoused]
  526 root         0 SW   [kworker/u:2]
  555 root       872 S <  udevd --daemon
  560 root      1724 S    -sh
  638 root         0 SWN  [jffs2_gcd_mtd3]
  716 root         0 SW   [romblock6]
  721 root         0 SW   [mtdblock6]
  727 root         0 SW   [flush-31:6]
  729 root         0 SWN  [jffs2_gcd_mtd6]
  731 root      1752 S    /bin/sh ./appinstall
  821 root         0 SWN  [jffs2_gcd_mtd4]
  930 root         0 SWN  [jffs2_gcd_mtd5]
 1178 root      1072 S    sysinit
 1213 root      1704 S    telnetd
 1268 root      1704 S    syslogd -O /tmp/syslog.log -s 64 -b 8
 1286 root     39424 S    ./AntsOnvifServer
 1291 root      1704 S    ntpd -l
 1411 root         0 SW   [flush-mtd-rwmap]
 1413 root      1708 R    ps

Что из этого убить ? И как его потом запустить ? А зачистить логи это как ?


Вернуться в «Видеокамеры IPC»